How to set up the TV DVB T2: step by step guide

DVB T2 needed for analog and digital signals. This allows you to watch channels in high quality.

How to set up the TV DVB T2

The setup process is the same for most types of receivers. May be different buttons and menu items, as well as a common interface window. But the algorithm is the same for all devices.

Connect to digital TV and to make setup easy. To do this, you need only connect the cable to the required connector, and set up channels. If your TV model is outdated, and can not receive such signals, you need to purchase additional equipment.

In the TV there is a connector for the antenna connector cinch, Scart (audio and video). Instead of the latter, the device may be an HDMI port. This is even better.

When you double-connected via HDMI and the tulip, you can switch the cable as needed. But it is better to use for viewing HDMI, because it guarantees good quality.

Reference! Also taken into account when connecting distance to the tower, transmitting signals. In order to effectively adjust the signal should be installed on the street-mounted antenna with an amplifier.

instagram viewer

What may be difficult

There are times when it is impossible to set the reception of DVB T2. If there is such a problem, you must make sure that the antenna is not damaged. If it is a whole, it is necessary to check the direction. The antenna must be directed towards the tower. Also, you must install it on the street, if you put in the room, it will block the signal. If the user does not know where it is located the tower, will twist the antenna. It is necessary to move very slowly and smoothly. Once the antenna comes into contact with the tower, the device will work.

Attention! There are errors in the automatic channel search. For example, the receiver found the little canals, or have not found them all. Help manual search.

Also, there are cases where the TV channels are found, but the quality of the show is very bad. Hence, the antenna is turned towards the tower, but contact with her bad. Try to move it a little bit. This problem can occur when the weather is bad.

DVB T2 Set up your TV: step by step

To set up, we need a device called a receiver. It receives signals and transmits it to the TV. Signal sources: the Internet, the dish or antenna. Receiver is configured as follows:

1. For a start it is necessary to get to the box and remove the coating film. If it is closed, it will lead to overheating of the device.
2. Cut the cable protection sheath. Its length is about 15 mm from the end. We clean the skin.
3. And the protective film are folded to fasten wire ports F.
4. Connect a cable to the receiver and the TV.
5. Tulip wire inserted into the ports of the receiver and the monitor.
6. You can connect to a TV antenna. It must be installed on the street (house wall, balcony). Now you can start customizing.

Note! One has to be careful during cleaning because there is risk of damage to the film covering the central conductor. It is needed for protection.

Setting up is as follows:

1. We are looking for the menu. There, go to the settings.
2. Default country must be set. If not, specify themselves.
3. Absorb the language area, search mode and format.
4. Set signal format. Most often this point is put DTV-T / T2. This means that the TV catches both analog and digital signals.
5. Begin channel search process. There need not do anything, the device will find all available channels itself. The search can be canceled at any time and continue later. If necessary, you can select manual way to search for channels. Standard means that the TV will find all of the channels that are not on TV. Hand implies a search only those channels that are needed. For example, the user only looks at sports, and he does not need channels with cartoons and serials. Manual search for a way to ignore the past. To implement it, you need to set the frequency that broadcasts the channels in the area of ​​residence. It can be obtained from providers or the Internet.
6. Once all channels are found or if you have decided to suspend a search, click the save button to avoid losing channels found.

When installing format DVB-T / T2 receiver will find all the signals available in the area where the user lives. But you need to install the antenna and turn it to the transmitter.