Wiring diagram to the standpipe towel warmer hot water: how to connect the heated towel rail with his hands

Since in the present conditions can be met infrequently heating in the bathroom, it is necessary to install the dryer on its own or ask for plumbers. However, in any case, you need to know the correct order of installation for the personal security and identification reliability.

What you need to know to connect to the riser towel warmer hot water

First we need to explore all possible variations of the design. Basic only four:

• Snake. It presents with a classic model that simply behaves during installation and is not a problem.
instagram viewer
• Ladder. Unlike the previous, according to a more modern version. Used in the different nature of the connection. But beneath all the conditions suitable.
• P or U - shaped. Standard and normal view. A widespread demand for high availability.
• The complex shape. It can perform not only the function of heating, but also act as decor to create an interior bath. However, everything is so bad, if you hold the correct connection. Otherwise circulation can not be ensured.

IMPORTANT! In addition, it is better to buy in the domestic construction of the seller-producer, and to comply with GOST standards. You also can not use parts made of different materials and with different diameter tubes need to use adapters. Do not forget about the power reduction by about 10%, if the pipes are connected to the bottom of the system.

Possible options for connecting to heating towel warmer

Of course, the introduction and can be of different types. The article is a look at each of them separately.

Bottom connection

It expected to be less effective actions. But still the standard and universal version that will durably be operated in either direction of feed in the riser. The principle of operation is very simple - the hot water comes from one side and comes out the other. In order not to lower performance optimal performance, you should:

1. Install the bleed screw so that they were on the upper terminals. It is necessary for deflating the air, which normally accumulate at the top.
2. The direction of feed pipes (proportion of about 4 mm per meter).
3. Bypass to get narrower and straight. And to make sure that it is obstructed, not otherwise it will slow down circulation and impair the water pressure.
4. The room in which the device is located, it is better to keep in isolation.

Bottom connection with the top water supply

Despite the fact that the supply takes place from above, outlet riser still has to be located below the upper boundary of the towel warmer. Because in other cases, it will not be included. However, if you remember, provided that the connection should be higher than the outlet, the unit will have to be, so to speak, pulling up to the ceiling.

REFERENCE! It is forbidden to create a "hump" or "loop" at the top of eyeliner. Because of this circulation will cease to operate accurately.

side connection

Well the fact that the use of all three standard forms can participate. And if we take the "ladder", then only need to put caps and vodootvodchiki not need. With this method requires the narrower bypass. Bends, in turn, must be definitely on the horizontal line. Operation is going to happen if they are from the top drawer. If all the recommendations will be met, the stability is guaranteed. There is also permissible but undesirable scheme under which require cranes Majewski. In this air bleed enlarge the dryer edges, so the user to periodically remove the air mass in the process.

diagonal connection

In principle, the performance is no different from the previous one, however, consumables need to spend more as tubes themselves overall. The water comes from a top side, a bottom outlet carried diagonally. Moreover, the bypass should life not narrowed and unbiased. In this arrangement, the feeders works with the most distant, while the last one is connected to one's neighbor. It is worth remembering that the chance is less than all the rest, a successful start-up, because the resistance of the SS increases.

Whether the form is important

From these characteristics will depend on type of device is connected, so is considered to be more or less important aspect.

When connecting with a heated towel rail "ladder"

ATTENTION! This can be done only with the fact that the system will be disabled. Therefore, you should first contact the housing office with a request to disconnect the riser. You will be assigned dates wizard. And then you can start the process.

Develop a plan, materials that will be useful. Read the instructions, which is written individually. In spite of this, has a total phasing.

• Playing the dismantling of this dryer.
• The connection of pipes and equipment.
• cranes establishment.
• Installation of jumpers.

Upon completion of the work should be to remove all the accumulated garbage and the ability to check the updated device.

REFERENCE! When mounting is desirable to adhere to a particular surface and the distance between tubes. For example, it may be 3.5 meters, if the diameter is less than 25 centimeters.

How to connect the "snake" to the hot water heated towel rail system

It is best to establish a universal side connection. But will have to use the grinder for removal. Pre carry out the same manipulation as usual - to disconnect from the mains and drain the water out of the riser. The actual installation is desirable to start with a bypass installation. A liquid transfer valve block and via two other secure mounting location unit. Following the step by step instructions that came with the design, you can open the pressure taps.

Wiring diagram towel warmer complex shape

In such a situation we will have to take into account some special features. The working pressure of 8 atmospheres, however, may experience up to 16 atm. For improved heating costs bleed screw, then the air will escape from the system. Installation is due to the special bushings. They are mounted on the wall. When fitting the hub legs to the screws used to fix the device certainly.

Main connection errors, and how to avoid

No one is immune from mistakes, that's fine. However, to reduce their number, consider the following recommendations:

• air pockets can form due to improper location. To avoid this, it should be placed in a horizontal dryer.
• the risk of leakage occurs most often in order to avoid this, do the replacement of the old to the new product.
• Still, if you do not have special knowledge and skills, contact the person in order to not unnecessarily pushing your luck.

Now you will be able to easily connect towel rail with his hands.