Furnaces for the garage with his hands: stoves, long burning, on working out, brick.

Usually indoors private garage in the winter it is very cold. Apply electric heating equipment is expensive and inefficient, so many car owners prefer to make their own oven, choosing for themselves the most appropriate option.

What can be done to the furnace garage

The following types of furnaces is most often used for the garage premises:

• stoves with wood;
• of the two drums;
• continuous burning furnace;
• the unit for working out;
• Stone embodiment of the heater.

Each option has its positive features and drawbacks. Therefore, for each individual processing host selects a more convenient and affordable device.

Stoves wood-burning heating garage

People who are not related to the production of plumbing believe heater Garage time consuming and complicated.

In fact, some units are so simple that they can be collected from the materials that are available in almost every car owner available.

Before you start assembling the design not only need to make a specific work plan and draw a diagram of the furnace for the future of the garage, but also to explore the pros and cons of the option selected. Consider the most efficient units, and the process of their manufacture.

vertical

This is the most common variants of the garage furnace, which can be made of materials:

• pipes;
• drums;
• gas cylinder.

The design is compact and ergonomic, plenty of space does not occupy.

assembly algorithm is as follows:

• to prepare a cylindrical part suitable for parameters;
• divide it into two halves, one large - for heating, the second small - ash pan;
• then these cells are settling square holes for doors, which are made of detachable parts;
• attach the hinges onto the door;
• in place of the cylinder section equip grate - grate of steel rods that are welded to the upper part of the ash is not more than 2 cm from each other;
• in the upper part of the furnace is cut hole for chimney;
• fix the pipe section of the desired length and, for the removal of carbon monoxide from the premises.

Vertical stove is ready for use.

horizontal

This second embodiment of the combustion arrangement portion stoves. The downside of this machine is its bulkiness, so constructing a structure only in large indoor garage. To manufacture can be used as a large cylinder or tube and a steel sheet of a certain section.

Instructions for the production of furnace:

1. Cut the piece into 2 parts is not necessary, the ash pan is made separately.
2. On one side of the container drill holes that will serve as pressure jet, and diverting the ash and furnace.
3. Craft rectangular ash pan made of sheet steel and welded to its bottom structure.
4. On one side of the product to cut a hole under the door.
5. Weld hinges.
6. In the upper part of the chimney pipe to arrange a certain section in a pre-make a hole.
7. Weld the feet to design precisely and firmly against the floor.

The oven is ready for a garage, you can begin to kindling.

Of the two barrels

The construction of the two drums devised to burzhujki walls do not overheat as it happens in the sheet metal furnaces. The heating unit is manufactured by the following method:

• 2 is selected barrels of different diameters, so that you can put one into another while maintaining the gap, which is filled with sand or gravel;
• doors for flue ash and construct so that the contents of the internal space is not spilled, closing it from sheet metal strips;
• at the top of the chimney equip with a pipe for discharging combustion products.

IMPORTANT! This design will warm much longer, but the heat it will be stored for a long period, which is important in the winter.

Wood furnaces long burning his own hands

This design makes it possible not to enclose the wood for a long time - 15-20 hours. This arrangement is achieved by means of a moderate thrust produhi. For this construction applies barrel volume of 200 liters.

The superstructure equip chimney diameter of at least 150 mm. You should also arrange a special opening for the air holes through which air will flow.

The next step in the door mounted to the firebox and ash pan. The final step is equipping the cargo, it needs to:

• produce a circle from sheet metal, smaller diameter than the drum itself;
• her several segments welded sill;
• hole in the disk equip a pipe section of 100 mm;
• barrels are welded to the bottom of the square metal sheet to stabilize the final structure;
• set the load in the drum and cover prearranged lid with a hole for the chimney.

The finished continuous burning furnace is mounted on a foundation of concrete or brick.

Stoves on the working out of a garage

This is a fairly efficient design, build that will be harder than the wood-burning burzhujku. The economic aspect of this furnace is obvious - the waste oil is at each motorist, in addition, the repair shops to buy this fuel is not difficult, and there is it cheaply.

The main difference of this design is the arrangement of two compartments interconnected by a pipe with prosverlonnymi around the perimeter of the holes.
In the lower compartment will burn oil and converted into gas which is moving in the second half of the furnace, is mixed with air at the combustion, it gives a lot of heat. In the first tank, which may be of any configuration, is mounted, adjustment poduv for air supply regulation.

Is welded to the bottom of the legs of a metal bracket that can withstand the entire structure. Further, to the upper part of the first chamber is welded thick-walled pipe with perforations in the initially prepared hole.

To the top of the pipe is welded a second chamber in the form of a cylinder, wherein the settling chimney. With this structure, any one can burn liquid fuel, which is not characteristic of rapid ignition.

Brick oven for the garage with his hands

Sometimes in a large garage set heating brick structure, despite the fact that its installation process is much more complicated all the units described above. Advantage of this design is the fact that the unit is heated for a long time, but long enough to cool down.

Brick oven need to melt advance 1-2 before you start working in the garage. For the construction of this design should be prepared and the desired amount of fireclay refractory brick.

ATTENTION! The brick oven is large enough specific gravity. Therefore, it is desirable to design a construct reliable foundation.

Constructing the heater in 9 rows, at 2-4, and spread ash pit furnace. Tube constructed of brick and output it through the ceiling and the roof, it is important that the masonry was flat, or the chimney is clogged quickly.

Build a stove in the garage any car owner can, if properly come to an arrangement of construction and follow the advice given above.