How to disassemble the monitor with his hands and did not nravredit?

Of course, each device tend to break down. For troubleshooting sometimes need to disassemble the pre-construction. However, not everyone knows how to do it right. Thus, this article will try to analyze in detail the specifics of the monitor analysis, as well as touch on issues that are strongly recommended to perform the process.

The procedure itself (open the monitor) can even perform a novice master, but it is important that all satisfied with the utmost care and precision, because the equipment is fragile and can be easily to harm.

What you need

Of course, before the main stage of the need to arm themselves with certain items that, accordingly, will be needed. Below is a list:

• Screwdriver, small size;
• Tweezers;
• Wedges made of wood;
• The sharp edge of the knife;
• Soft cloth to put on her design. This can be as a blanket, rug, or any carpet.

Prepare the monitor for an analysis

It is important to understand what is really appropriate for the work necessary to prepare the workplace. It is necessary that in the process you nothing could interfere with and prevent the achievement of goals. Thus, for the beginning user, most likely, it will be necessary to remove the leg on the screen. Most often, you will notice a mount, which uses screws that connect the body with the main part. They are, of course, unscrew and carefully make the withdrawal.

As for the rear panel, so it is not only the possibility of a small screwdriver, wedges, but also due to the screwdriver in the amount of two pieces. Therefore, it needs to pre-push one into the opening between the front and rear panels, after which they were carefully apart. The next step is the penetration of the same article, however, is in a sideways condition.

Forward movement it is desirable to smoothly penetrate through both sides of the wobble. click edition would mean achieving the goal - the flap opens. Gaining all the details you need to separate from the sidewall latches up until fully open the rear of the monitor.

ATTENTION! In order not to hurt the surface, it is possible to use certain tools that easily can be purchased at specialty stores.

Instructions on how to disassemble the cabinet

After the preparation phase, respectively, can start by the main workflow, as described below:

1. The first thing you need to deploy monitor the front side facing down. With the same view, you can see the tabs, you need to detach using forceps, thereby pushing back the cover.

REFERENCE! Do it with maximum caution is recommended, leaving a gap of half a centimeter to one. This need is due to the fact that there is a likelihood of damage.

1. Next, one should arm themselves with wooden wedge and push it directly into the hole made. It is necessary to ensure that the gap could not slam.
2. Therefore, such manipulation is necessary to spend to other places, where the latches are located. How many of them - it is impossible to predict in advance, as each screen models tend to their number.
3. When you get to the upper parts will help screwdriver. With it you can get through a rather narrow space, it should be a little press on the surface.

IMPORTANT! It is at this point the risk of injury is high, so it is strongly recommended to perform slowly and carefully.

So usually after such shenanigans cover removed quite easily. Once opened, you will see a metal casing.

What can not be / is not recommended

Of course, there are certain aspects, the performance of which may entail unpleasant and sometimes disastrous consequences. Thus, to your attention is provided a list of these undesirable things:

• Using a large screwdriver. As the material with which you interact quite fragile, the same heavy objects can cause various injuries.
• In principle, disassembly must be carried out only when the user is convinced of the need and usefulness of the resulting one hundred percent. This is due to the fact that most of it will be better to consult a qualified expert.
• The work itself should be carried out in complete safety.

ATTENTION! The device must be disconnected from the power mains.

• Performing the procedure is better to do directly on the floor. Otherwise, even if dropped structure from any height, provided the owner lethal equipment. Therefore, in the best situation, the monitor will have nowhere to go, that acts as a guarantee of preservation of your facilities.