Proper cleaning of the vacuum cleaner: a sequence of actions

No surprise that the modern housewife ordinary broom and a vacuum cleaner prefer panicle. Cleaning with it is faster, and it copes much more efficient in collecting small debris. But do not forget that, like any complicated appliance, this device is maintenance-free. You need to know how to clean it at home, so that the cleaning was a joy, even many years after the purchase.

When you want to clean the vacuum cleaner

Ideally, you should brush your device after each cleaning. When such care vacuum cleaner will last much longer. Before storing it, you need to perform a few simple steps:

• Check the nozzle for contamination and eliminate them.
• Throw garbage from the cyclone filter and bag, and wash them.
• Wipe the body of the appliance from the settled dust.

Important! When cleaning a small area to carry out data manipulation is allowed after every second or third operation.

As pollution Clean debris from the pipe and tube, as well as foam rubber and HEPA filters.

As vacuum cleaning is carried out

To not inadvertently break the working parts should comply with certain rules in their purification.

Important! Before wet vacuuming, disconnect it from the mains. Otherwise there is a possibility of electric shock.

Filters of different types

The type of device depends on a way to care for them.

With disposable bags

The easiest to remove the debris became a vacuum cleaner disposable bags. When filling the bag simply disconnected and discarded, and replaced by a new set.

Reference! As a rule, when harvesting in slightly contaminated apartments original dust bag is enough for a few months of active use.

But such devices have a slight negative: The accumulation of dust suction power slightly, but still reduced.

With reusable bags

Some fabric bags for dust are reusable. In this case, they are allowed to shake or wash after the devastation of garbage.

Important! As wear reusable bags and should be replaced with new ones.

With aquafiltering

Aquafiltering the most effective in terms of dust retention. Him cleansing dirty water is replaced by clean washing and walls.

From the cyclone filter

Cyclonic filters desirable wash after each cleaning. Rubbish is thrown out of it, and the bowl is washed with water and dried.

HEPA filters

There are one-off, but there are also reusable options.

To clean the HEPA filter, it is necessary remove from the surface of larger particles of dust and hair and then rinse in soapy water.

With foam filters

The same goes for foam filters.

Important! Pressing either foam or HEPA filter can not be. This can damage the structure to deform the product and lead to faster wear.

Activated carbon filters

An excellent job with dust and unpleasant odors. But Cleaning it is not intended!

With a strong desire, you can go over the surface with a brush to remove some debris.

Important! When worn and very dirty, the charcoal filter should be replaced with a new one.

brush

In the basic configuration to a vacuum cleaner are always a few tips. They are just like the other parts in direct contact with the mud, need regular cleaning.

• To begin, go over schotke other attachment or just a pipe. This is done in order to maximize clean stubble or catching surface of the adhered debris.
• Is wound on the rotating parts hair and thread can be removed with scissors and forceps.
• A damp cloth to remove dust from the accessible surfaces and blades.
• If the nozzle is very dirty and difficult to clean her hands can be washed with a brush under running water. However, before reusing it is required to dry at room temperature until complete evaporation of moisture.

Hoses and tubing

These details are often clogged with large debris. If this suddenly happens, you should immediately release the lumen. Otherwise the suction power falls critically and increased load may cause the engine to overheat.

• You need to disconnect the hose from the housing.
• If in the lumen is clogged, it can be removed with a long object (metal wires, wooden or plastic stick with a hook, forceps).
• Rinse the parts inside the jet of water. You can use a sponge if desired.
• Walk outside with a damp cloth to remove dust.
• Dried and set in place.

Motor

This is the heart electrical equipment. It is not necessary to disassemble it, if not confident in their abilities. Should be entrusted to the engine cleaning professionals. The service centers are almost always offer this service.

But if you suddenly have a desire to do the work yourself, you need to adhere to the following steps.

• Remove the dust bag, remove bolts on the case and remove the cover.
• With panicle or brush dust gently walk on detail. It is important to do it carefully so as not to disturb the position and attachment of wires.
• Remove the chip from dust and blow fee.
• Install all the parts into place, close the cover and tighten the screws.

If everything was done accurately, the device will work with renewed vigor.

housing

Many vacuum cleaners do not have a very good property. They collect dust on a plastic surface. Also on glossy casing very visible greasy fingerprints from fingerprints and stains.

Wash the body and the handle is not difficult. You do not need to carry out some complicated manipulations and disassemble the vacuum cleaner. simply walk on the plastic surface with a damp cloth or tissue. If necessary, it is possible to use special fluids for removing fat (detergents, citric acid, vinegar, hydrogen peroxide, water micelle).