Why noisy faucet in the bathroom How to fix the problem, if the noise mixer

Breakage of plumbing devices designed to make our lives more comfortable, have different causes and therefore the "symptoms" have different. Something is clearly evident and easily diagnosed, but something did not notice. Agree on buzz faucet few general turn their attention. Well, buzzing, buzzing, and let him continue. so maybe it should be. But it was not there. No hissing, humming and other such liberties should not be sanitary. This is clearly a malfunction of equipment.

Why noise mixer in the kitchen or bathroom

The noise coming from the mixers of various types, has several causes. Most often, such designs emit noises having the rubber gasket. But the same noise possible in the ceramic head parts - here there is already married, admitted in the production. Much less likely to emit noise lever mixers.

If the noise issue at the same time both gates of the mixer, it may be a consequence of the great water pressure - it is often the case in modern high-rise buildings. Cheap products do not boast massive body, so there may be microscopic cavitation and water hammer.

Reference. Very noisy blender at a time when there are pressure drops in the water.

Often under the noise of the mixer is meant noise from the liner. Opening the gasket, it is necessary to pay attention, whether fixed securely and whether the pipe fasteners available. This would eliminate juddering. A similar situation in the case of hard-liner is much rarer.

How to fix the problem, if the noise mixer

Determining continuously opening and again closing the water, which noise comes from the mixer definite need to eliminate the problem. Most often the cause of hum - wear locking parts.

Based on the type of control device, all mixers can be divided into two types. Mixers with a single lever and the cartridge, as well as devices with valves. Techniques for correcting damage will differ depending on the type of constipation.

Remedy in the single-lever faucet

The faucets with single lever cartridge is completely reliable. In it there is a plate made of ceramics, which is covered water. During operation, wear plate - from this and there is a whistle and noise while the water supply and its ceiling. In addition, noise may appear unnatural and natural wear of the gasket.

Typically, the cartridges can not be repaired, although it is possible. They are easier to change, it is quite possible to do on their own. If we look at the attached diagram, it becomes clear how to do.

Reference. After the lapse of time laying harden. If such a gasket lubricate silicone, it will become elastic again.

Remedy in the valve mixer

The reason for the noise in such a device - rubber gasket wear or damage it. Perhaps, when the valve is too long, laying just flattened. Then the new crane will make a noise, even if the water does not go - in fact flattened lining its edges extends beyond the seats and the water pressure causes it to twitch.

Head parts of modern mixers are of two types. They can be poluoborotnymi and have liners made of ceramic and can be brushless and have a pull-rod.

The technology works by changing the gasket is different for each type of axle box. In general, everything is done as follows.

Attention! Before disassembling the mixer, make sure that the water is blocked in the central riser.

To replace the gasket in the journal box of the valve type, adhere to the following plan:

1. Remove the cap from the valve handle, unscrew the mounting screw and the handle can be removed.
2. Twisted head parts of the housing.
3. With the help of pliers to unscrew the washer, which fixes the gasket. Since the washer can prirzhavet better to sprinkle it on the HP-40.
4. After all this, you can put another gasket and assemble everything in reverse order.

Attention! At the edge of the pads are beveled at an angle of forty-five degrees. Its narrow side, it is set on the saddle. If for no apparent reason in the repair kit is not required pads, and are only available with straight edges, then you need to cut the edge of one millimeter at the desired angle. After that, the gasket firmly snaps into place and does not flatten when the valve is delayed.

If you need to change the pad axle box having inserts made of ceramic, it similarly be extracted from the mixer body.

After the bush is disassembled, the gasket which is located in the lower part of the device to hook with a screwdriver. In its place set another gasket. At the same time it should be a little pre-load to be placed in the slot, and then press.

Getting rid of noise when switching the mixer on shower

Very often, when the mixer is switched to the supply of water in the shower, there is a whistling sound or noise. The most common reason for this - foreign objects clogging the switch. The switch has a very small diameter inlet and outlet openings. They are so small that even a slight reduction from their original size causes noise.

Very easy to get rid of this problem. It suffices to examine the switch and carefully clean all parts of the flight rust, deposits and all other foreign bodies.

In concluding our story, I want to note that the cause of the "vocal" in conventional mixers - it is too strong pressure within the water supply system, as well as normal wear pads. Normally, all this can be remedied without recourse to outside assistance.

But do not pigeonhole search for the cause of the "behavior" of the mixer and the removal of this reasons, because the consequences may worsen and cause more severe fault, and there before the accident near.