How to disassemble the headphones: vacuum, wireless, how to disassemble the headphone plug

Headphones are made of wires, plugs and a pair of speakers. In addition, the headset can be equipped with other elements that expand the scope of its application. Each of these elements during the operation may fail. Before attempting to repair should understand how to disassemble the headset or earphone vacuum in order not to spoil the headset. Consider the features of disassembling the main headphone categories examining this information, you can easily cope with any headphones, especially because of all similar.

How to disassemble the headset with microphone

Often the event of a breakdown of staffing headset additional features. These elements are placed in a small plastic case for ease of use which is mounted on a cord. In order to get to these elements is necessary to disassemble the cabinet. It is usually glued and to disunite the two halves of the need to use a knife.

Damage is the volume control can be identified by characteristic crack in speakers or poor sound. This problem is formulated as a variable resistor. This item consists of a slider that moves along the resistive layer. Extend the life of the element can be using graphite grease. Lubricate elements using a cotton swab.

Problems with the microphone manifest deterioration in hearing during conversation. The reason is often clogged. To resolve this problem, you must wipe the microphone using a cotton swab, which was pre-soak in alcohol. When all manipulations performed, you can glue the two halves of the case.

How to disassemble the vacuum headphones

If there was a failure of the vacuum near the headset speaker is required to disassemble it. The algorithm of your actions should be as follows:

1. Locate the seam on the earphone housing. It is necessary to work with a knife or other thin, but strong element. To razosholsya seam on the body can be a little push pliers.
2. When the housing is open, you can see the inside of the headset. This speaker with contacts. With the help of a soldering iron, disconnect the damaged veins, but above all it is necessary to mark the color of the insulation. Use a marker to further avoid confusion.
3. Of the total cable headset need to cut junk item. The working wires Strip wires and solder them to the speaker terminals. Clearly follow your notes in the insulation.

To diagnose the correctness of the work performed, connect the headset to the gadget, including music. If everything works as it should, glue half the disassembled body. The same principle can be dismantled and bluetooth headset.

How to disassemble large wireless headphones

If you have failed big headphones they can also be dismantled. The speakers are hidden inside the body, it becomes more difficult disassembly of the fact that there are hidden screws and latches. If parsing you will not find all the elements you can simply break the plastic parts.

IMPORTANT. Different manufacturers use different headphones fastening methods, be careful.

Consider a few basic options:

• For example, to parse the Sennheiser HD203 headset first need to remove the ear cushions. These pads are attached with special latches, they can be easily disconnected, armed with a conventional plastic card. Under padded you will see 4 screws. Unscrew them using a screwdriver.
• the housing halves are not glued together. Once you twist the screws will not be difficult to separate the elements. The front panel is fitted to the dynamics of their contacts need to solder a new wire, if the old is out of order.

Other manufacturers may be glued soft linings, in this case for their removal need to use a knife or a screwdriver. Fastening halves may be accomplished with screws or latches. When parsing the headset, be careful, do not rush to break off nothing.

How to disassemble the headphone plug

If the work is something wrong headphones, you need to pay attention to the plug. A very common cause of failure is bend cable conductors at the connection with the plug. Detect such breakage is easy. You need to activate the headphones and play music, shifting fingers bend place you should hear a crackling or any noise. This indicates a problem with it at this point. Therefore, it is necessary to disassemble the connector and fix it.

For repair, follow these steps:

• With the help of pliers, remove the cable from the plug.

PURPOSE OF REPAIR. Extract from the metal part of the braid. Keep in mind that the element is securely soldered and keep the braid you will not succeed.

• Metal part of the plug gently reach for, it is important not to damage the contacts. Keep soldered wiring. The color of the insulation is easy to figure out where to solder the leads.

REFERENCE. If the headset is equipped with a microphone, then, under the braid you will see not three, but four cores.

• The cable that you are separated from the plug will need to be cleaned. It will be enough to take the 5 mm of insulation to be able to solder the copper wire to the plug.

IMPORTANT. Veins of wires coated using a wired varnish, it prevents spikes. For the work necessary to clean off or scorch the coating.

• Make a new cover for the connector. To do this you need the cap from ordinary pens. Put on the wire piece of heat shrink tubing. This will reduce the likelihood of re-damaging the wire in the same place. cable conductor must be soldered to the connector contacts. Do not forget about the color of the wires and their compliance.

• For testing use the tester. In either case, you can connect the plug into the device and play music. If everything works well, heat shrink tubing. Push cap after coating it with epoxy.

Process disassembly headphone relatively simple task. The main thing is to do everything carefully and do not rush. Having familiarized with the given information, you can easily fix the problem and keep your headset, and continue to operate it.