What to do when water is poured directly from the tap and shower

Malfunction of plumbing negative impact on the comfort and quality of life. All items in the bathroom should be given due attention in order to avoid unexpected breakdowns. But sometimes the fault is still taken by surprise. One of the problematic situations is the simultaneous supply of water from the tap and shower.

Causes of water at the tap and shower at the same time

The water that pours from two points, adds convenience when using the bathroom. To solve the problem, you need to figure out its cause. There may be several.

Drying and punching pads

Rubberized part thinner. This leads to disruption of the mode, the shutter can not be closed tightly. Therefore, the water pressure is distributed unevenly.

If the problem is in the pad, it should be replaced.

Important! As it is not a design, there are two. And both should be changed immediately.

Erasing the rubber ring, the problem button or omentum

The rubber ring and its quality refers to the most common failure.

Both of these faults are caused by one of the following reasons:

• Low quality mixer. The modern market offers a huge range of different price categories. Among them there are defective products and poor quality items. They have a short lifespan. Operational problems begin to appear quickly.
• Ephemeral supplies. It is important to use not only a good mixer, but also qualitative elements for repairs. Otherwise, failure quickly again.

Such damage can be repaired by yourself. No special skills and knowledge. However, it is important to use with only quality parts. Then the problem will be solved for a long time.

Remedy

Before proceeding to repair, it is necessary to examine security measures. Their observance will avoid unpleasant situations.

Safety regulations

• When you perform any kind of repair first completely cover the water. This applies to both the hot and the cool.
• Be sure to then open the tap and check whether water flows. This is because the valves can also be broken. These actions will ensure that things are really blocked.
• Working with hot water, it is important to be careful to avoid scalding.
• Spinning fixture, it is important not to push too hard or you may damage the threads.

repairs

Switches to tap on the shower taps have come in several forms. It Rod-operated button is pressed. Or ball, triggering the switching mechanism by turning parts.

Depending on the damage may require replacement of gaskets, rings or completely switch.

replacement pads

• After the water is blocked, open the valve and release the pressure balances.
• Then clean the trim that hides the main part of the switch.
• Remove the bolt holding part, and a handle.
• Switch itself spun using a wrench. We need to move counterclockwise.
• Remove the liner from the construct and inspect. If her condition is normal, simply wash the item. But if it is dried out, then change it to a new one. Purchase item can be in either the sanitary shop.
• Under the first spacer is a second. To extract it is necessary to remove the ring nut and gland packing.
• When managed to get to the second spacer, it is also changing.

replacement rings

If the problem is in the rubber ring, it is also changed to a new one. Technology similar to that described above.

But to get to the details, you must not simply parse this part of the mixer. The adapter must be removed from the construction. You can use for this purpose tweezers or just push from the bottom, where the hole in the crank case.

Important! After replacing any parts of the mixer, it is necessary to assemble in reverse order.

Repair button

Problems can be a button, if you are using a switch spindle type.

If it just will not be returned to its original location by pressing, then, a broken spring. Mixer dismantle and change the button on the new one.

Replacing the oil seal

But when the switch is completely stopped working, the problem is in the stuffing box. It is located in the rod-end switch. Repairs carried out in the following order:

• Remove button.
• Extract the stem.
• Changing to a new oil seal.
• The reverse is going to switch.

In concluding, it should turn the water on and check whether the plumbing work was adjusted.

To rectify the situation, when at the same time water flows from the shower and parts of the crane, it is possible. It is enough to figure out exactly which part is broken, and replace it. We hope that the problems and difficulties at work, you will not.