How to apply liquid wallpaper to the ceiling, instructions, nuances

Liquid wallpaper is one of the popular finishes. They are used for various surfaces. The main thing is to correctly prepare for the process. When applying liquid wallpaper to the ceiling, it is enough to cover the surface with the material and wait for them to dry. A minimum set of tools is required. It is worth understanding the nuances in more detail.

How to apply liquid wallpaper to the ceiling: features

The process of applying such a finish is simple and consists of several stages. First you need to prepare the surface, then it is covered with the selected finishing compound. It is important not to neglect the first step. Preparatory work allows you to get a flat surface on which the finish will lie smoother and last longer.

What is needed for application

They start with the acquisition of everything that is needed for the work. Among the tools are:

1. A container of a suitable size. It will accommodate material and swell.
2. Spatula or trowel. With this inventory, the wallpaper will be applied to the surface.
3. Roller. Suitable made of rubber or foam rubber.
4. Plastic graters.
5. Embossed roller.
6. Spray.

You can make a trowel with your own hands. For this, a triangle with equal sides is cut out of plexiglass. The length is about 6cm. For convenience, a handle is attached to the resulting fragment.

How to prepare the ceiling yourself

The next step is to process the base. Liquid wallpaper has a high degree of adhesion, which allows them to be securely attached to various surfaces. However, preparation should not be neglected. This contributes to obtaining a high-quality, solid base, without serious defects, cracks and previous cladding.

Preparation consists of the following steps:

1. The old coating is removed. The suitable method depends on the type of material. Paper wallpaper needs to be moistened abundantly, and paint is removed mechanically.
2. Large cracks and chips are putty.
3. The surface is treated with a primer. A colorless or white shade will do. The main thing is that it contains quartz dust.
4. If there are metal parts on the ceiling, they are covered with water-based paint. This will prevent the development of corrosion and rust.
5. Plaster or putty is applied to the surface.

The ceiling doesn't have to be perfectly smooth. Such a coating fits better on a rough base.

Material calculation

To determine the amount of wallpaper, you must first measure the area of ​​the ceiling. The thickness of the applied layer is also important. On average, 1 kg of finishing compound is required for 3-4 m². Such wallpaper is applied in a layer of 1–3 mm. But if the surface is full of defects, you need to increase this figure to hide the irregularities.

When calculating, the resulting figure must be rounded up. It is important to remember that a certain amount will be required as a reserve. If the base is uneven, add from 7 to 13% to the resulting calculations. When a beginner performs the work, the margin should be 15%.

It is not always possible to find the exact shade of the material when purchasing it again. Therefore, it is better to buy more in order to have enough.

Application process

It is more convenient to work on a stepladder. The area to be treated should be in front of your eyes and clearly visible. It is necessary to apply the mass, holding the instrument at a slight slope. Do not put pressure on the spatula, otherwise the veneer will not turn out slightly loose. If you do the work without stopping, the joints will be less visible on the surface.

When the mass is well swollen, it is applied with a spatula in an even layer. Using a smooth trowel, level everything. Then cover with a new portion of the mixture so that the seams between the areas are not visible.

Important! Which position the fibers take depends on the direction in which the material is smoothed. Another trajectory allows you to change the decorative effect.

It takes 24 hours for the mass to dry. Do not use additional equipment to speed up the drying process. Liquid wallpaper should dry naturally.

Adding moisture resistance to the surface allows treatment with acrylic varnish to increase the service life of the cladding. This is the final stage when the main finish has already been applied.

After applying each layer, it is recommended to carefully inspect the treated area. There should be no tearing, bumps, bubbles and other things. It will be more difficult to correct such shortcomings later.

What are liquid wallpapers, their features

This type of cladding has a complex composition. The material is divided into several types. Among them:

1. Cotton. They are monochromatic and textured.
2. Silk. The threads can be natural or synthetic. They differ in elasticity, a variety of textures.
3. Cellulosic. Consist of wood fibers, which are preliminarily dissolved.
4. Combined. The composition includes cellulose mixed with some silk and cotton.

Also, the material consists of special additives for decoration, such as sequins, threads, seaweed and others.

One of the significant features of liquid wallpaper is the absence of noticeable joints on the surface. There is no need to painstakingly adjust the drawing, which saves time. It is easy to care for the coating: it practically does not accumulate dust and is unpretentious.

The porous structure of the material allows it to serve as additional sound and heat insulation. Easy and quick to apply. Even a beginner can cope with the task. If mistakes were made during lining, they can be easily corrected by covering the defective area with another portion of the mixture.

Liquid wallpaper is a modern material that allows you to create interesting and practical cladding options. They have a lot of advantages. Easy to use, with a wide selection of colors and textures. It is only necessary to prepare well the base, tools and correctly calculate the required amount of mass.