How to disassemble a Bosch washing machine? Step-by-step washing machine repair algorithm - Setafi

It is not difficult to understand how to disassemble a Bosch washing machine - all actions are performed in stages, using screwdrivers, keys, a hammer and a chisel. In some cases, you may also need WD40, which is better to buy in advance. Step-by-step instructions for dismantling all elements of the device with a photo and a description of the actions can be found in the material presented.

Preparatory work

Before you disassemble the Bosch washing machine, you need to understand its device. This is important in order to understand where which part is located (for example, the heating element is located under the tank in front, and not in the back).

The dismantling process takes place in several stages - first, all panels are removed, including controls, as well as a tray for laying the powder. After that, disassembling the Bosch washing machine comes down to the phased removal of each part. A basin, a rag, as well as improvised tools are prepared for work:

• a set of screwdrivers (including slotted ones);
• a set of hexagons;
• hammer;
• pliers;
• wire cutters;
• torx;
• bit.

You also need to turn off the device from the network in advance, close the tap, and, if necessary, drain the water from the inlet hose. It is unscrewed and the free end is directed into the pelvis. The unit must be placed conveniently so that there is access from each side. Next, you can proceed to study the instructions on how to disassemble the Bosch washing machine.

Dismantling of panels

The dismantling process takes place in several stages, and first you need to remove all the panels. The sequence of actions is as follows:

1. Open the door and remove it from the hinges by removing each screw. You need to work carefully at this stage so as not to scratch the glass.
2. Next, bend the cuff and remove the clamp. You can pry it off with a screwdriver and pull it off. The rubber seal itself is tucked into the drum.
3. Then disassembling the Bosch washing machine comes down to removing the bolts that secure the lock. To do this, you need to get a device that blocks the hatch - put your hand behind the case and remove the mechanism. Several wires go to it - they are also disconnected.
4. Unscrew the screws that run along the front panel and remove the cover.
5. After that, the panel is removed from the back, unscrewing each bolt along the perimeter. Behind the panel you can see all the main parts, as well as counterweights. These are the heaviest blocks (made of concrete) that also need to be removed. They are unscrewed with a 14 wrench.

Dismantling of internal parts

Then the analysis of the Bosch washing machine moves to a new stage - you need to get to the tank. But for this, all elements that are fixed to it from different sides are first removed. The instruction is this:

1. The dispenser tray is removed and the pipe that leads to it is dismantled. If there is a clamp, it is unclenched with pliers. At the same time, remove the pipe from the inlet valve.
2. Next, remove the sensor that controls the water level (pressure switch) and the filter. To do this, remove the wiring and unscrew the bolts on which these nodes are attached. A tube comes to the pressure switch - it also needs to be removed.
3. Now you can understand how to disassemble the Bosch washing machine from the back. First remove the drive belt from the pulley. It is very tight, so it takes a lot of effort.
4. Disconnect the wires that go to the electric motor.
5. Unscrew the bolts that hold the motor.
6. Slightly swinging the engine to the right and left, it can be removed from the housing. It is necessary to prepare for the fact that the element is very heavy - it will take effort.
7. The next step in the instructions on how to disassemble the Bosch washer is to remove the pump. The unit is laid on the left side and the bottom is removed (in some models it is not). To do this, unscrew each bolt.
8. Using pliers, remove the clamp that secures the drain pipe and dismantle the part. Remains of waste liquid may accumulate in it, so you need to put a rag on it.
9. Unclench the wires that lead to the pump, and unscrew the bolts with which the pump is fixed for draining.

Dismantling the tank and disassembling the drum

We disassemble the Bosch washing machine further. The advantage of this manufacturer's models is that the tank is collapsible. Therefore, it remains only to remove it and get to the drum. The algorithm of actions is as follows:

1. Disconnect the pulley. To prevent it from rotating, put a prop or other fixer. Unscrew the bolt located in the center. At first, it may not succumb - then you can use the WD40 tool.
2. Remove the bolts along the perimeter, which fix both halves.
3. Next, remove the upper part - it should turn out approximately the same as shown in the photo.
4. The tank is turned over and, by tapping on the rod with a small hammer, the base, that is, the drum, is removed.
5. Then, if necessary, you can get the bearing and remove the seals - if they are worn out, it is better to replace the parts completely, even if some part looks new.
6. Install the chisel on the bearing, as shown in the photo, and knock it out with a hammer, moving around the circle.

From this instruction it is quite clear how to remove the top cover of the Bosch washing machine, remove other panels and internal parts. It is quite possible to dismantle them yourself. Difficulties can arise only when disassembling the engine or tank. But if you understand how to disassemble a Bosch washing machine, you can deal with these details.