How to heat water in an aquarium? Install the heater yourself! – Setafi

oatLaRB

aquaforum.ua

Why have we prepared this material and who might find it useful? This question will only be asked by those who do not have an aquarium at home. The answer is simple: aquarium fish are mostly tropical inhabitants, so the room temperature of an apartment on the 3rd floor in Mytishchi is definitely not suitable. It needs to be warmed up.

In this article, we will talk about how to install a heater in an aquarium, as well as other ways to heat your favorite pets. Get comfortable, we're getting started!

The content of the article

  • How to make a DIY aquarium heater
  • How to heat water in an aquarium - method number 2
  • Critical option when nothing is at hand
  • Installing a heater in an aquarium

How to make a DIY aquarium heater

In this section, we will talk about the oldest means of heating a glass bulb - a reflector. It is not so difficult to manufacture, so it can be made at home from improvised means. To do this, take a tin half-cylinder, fix the cartridge with an incandescent lamp at the end. It should turn out so that the lamp is inside the reflector.

instagram viewer

Then we hang the device to the edge of the aquarium in such a way that the upper part of the reflector is under the water level. So the glass will warm up evenly and will not burst from temperature changes. The method is still good today, especially for tanks up to 30 liters.

How to heat water in an aquarium - method number 2

For this we do not need a tin reflector. Simply immerse the incandescent lamp in a container of water. We fasten the cartridge on the lid in such a way that it does not come into contact with the liquid, but only the glass flask is placed in water. The method has more advantages than the previous one, since nothing needs to be crafted. But one small drawback - over time, your light bulb will become overgrown with algae, and it will need to be cleaned.

Critical option when nothing is at hand

If, God forbid, the temperature drops by more than 10 degrees, then ordinary vodka will help to quickly stabilize the situation. For this:

  1. pour some liquid into the tank (ratio 3:10, for 3 ml of vodka 10 liters of aquarium water);
  2. after the procedure, install a carbon filter until your pets stabilize;
  3. then change a third of the fluid in the tank.

Installing a heater in an aquarium

5_big

aquaforum.ua

There is probably no better way than buying a ready-made special heater in the store. It looks like a long tube containing an electron spiral. The inside is also filled with quartz sand. The coil outlets are at the top and are carefully sealed. By 220 volts, the device is powered by a wire.

The power of the heating element is different. Choose for yourself such that the upper area of ​​the test tube with all contacts is at least 2 cm in height from the waterline. In this case, the lower part should not touch the bottom. Power can be calculated by eye: 30 watts is suitable for a 30-liter tank.

To fix the system inside the aquarium, use rubber suction cups or plastic rings with fasteners. For simplicity, if you did not find any accessories, install the test tube with a simple wire. Only it needs to be fixed at the top of the tank, and not in the water itself.

Heating an aquarium cannot do without a high-quality thermostat. They should be sold where you found the bulb with the lamp. Temperature control will be much easier if a special thermometer is at hand.

It also does not hurt to buy a filter system so that warm water circulates evenly over the entire plane of the aquarium. You can try to put a small compressor - also a very good solution.

Do you know how to heat water in an aquarium? Tell us about your methods in the comments!

Foam block toilet: how to insulate a winter bathroom for a summer house – Setafi

Foam block toilet: how to insulate a winter bathroom for a summer house – SetafiRepairHome

Building a toilet from foam blocks is a cost-effective solution for a summer residence, due to the thermal insulation properties of the material and ease of installation. Foam blocks have a porous ...

Read More
Volume of water in the heating radiator: how many liters in a section, table – Setafi

Volume of water in the heating radiator: how many liters in a section, table – SetafiHomeAir Conditioning Equipment

Finding out how much water is in the radiator is very important for the heating system to work correctly. The amount of water in the radiator directly affects how well it can heat the room. It also...

Read More
Insulating a house made of expanded clay concrete blocks: how to insulate the outside – Setafi

Insulating a house made of expanded clay concrete blocks: how to insulate the outside – SetafiRepairHome

Insulating a house made of expanded clay concrete blocks is an important process that is necessary to improve the thermal insulation properties of a home. Expanded clay concrete blocks, due to thei...

Read More