Philips Saeko coffee machine: malfunctions, repair methods, warranty cases - Setafi

Malfunctions of the Philips Saeko coffee machine are very often associated with the brew group. It can be very clogged or even not installed correctly. How to act in different situations, and what causes are observed most often, is described in the article.

Frequent breakdowns

Most often, the Saeco coffee machine does not pour coffee or only clean water flows out of the machine. These cases refer to the warranty, if the service period declared by the manufacturer has not expired.

No grinding of grains

Outwardly, this malfunction will manifest itself in the fact that only hot water flows out of the apparatus. The reason is related to the large load of the coffee funnel.

You just need to pull it out and remove the stuck grains with a teaspoon. You should make several movements in a circle, without too much pressure on the cake. You also need to keep in mind that if the machine is equipped with a removable container, grains can get stuck between its fragments. Then it is recommended to pull out the container, disassemble it into parts and clean it manually as well.

Coffee not pouring

If the coffee machine does not pour coffee or it comes literally drop by drop, the reasons are related to clogging in different nodes:

• brewing block;
• spout through which coffee is served;
• water filter (it can get very clogged or a mistake was made during installation).

The first thing to do is to clean the spout with a needle, then rinse the brewing unit under the tap. When it dries, all contacting elements are lubricated. Then the filter is removed and the coffee is prepared empty, that is, without it. If the drink goes well, then the reason is connected precisely with the filter - it is better not to clean it, but simply replace it with a new one. It is also recommended to carry out 1-2 cleanings with special decalcification tablets.

Water under the machine

In this case, the reason is obvious - there is too much water in the pan. It must be periodically cleaned and drained. Moreover, they do this after the appearance of the corresponding indicator on the scoreboard - it is not necessary to specifically monitor the capacity.

No milk foam

This malfunction is associated with a clogged pipe from the cappuccinatore or incorrect installation of the milk pipe. In rare cases, the use of the wrong low quality milk can be affected.

First you need to check the position of the spout - it should be fully open. Then, if the machine still does not work correctly, disassemble the milk jug and rinse it thoroughly under hot running water. It is also recommended to replace milk - it should be whole cow or soy.

The coffee is too watery

In this case, the causes are related to the brewing unit or clogging of the coffee funnel. It is necessary to remove and clean the relevant parts and install them back.

Cannot remove brew group

This clearly indicates that the element is not set correctly. You need to disconnect the device from the network and wait a minute. Then turn it on again and after 30 seconds remove the grounds container, as well as the drip tray. Then try again to get the brewing mechanism. But if this does not help, it is better not to take risks and call the master.

Common Error Codes

As a rule, if the Delonghi or Saeko coffee machine does not turn on or does not work correctly, it carries out diagnostics on its own and indicates the corresponding code on the scoreboard. The most common types of errors look like this.

E01

Indicates that the beverage funnel is heavily clogged. It needs to be removed and cleaned. And if there is no funnel, they take a teaspoon and insert it into the tube with a handle, make several circular movements.

E03

Talks about problems on the part of the brew group - it can become clogged. Or the block parts are not sufficiently lubricated. You need to disassemble it, thoroughly clean it and apply a food grade lubricant.

E04

This code is also associated with the brewing unit. It may become clogged or incorrectly installed. It is necessary to remove the device, clean and lubricate. Then correctly put, having heard a click.

E05 or E14

This code indicates the machine is overheating or other problems. It is necessary to disconnect the device from the network and let it stand for at least an hour. But if this does not help, you should not make repairs yourself - you should invite a specialist by calling the service center.

These and other errors are observed more often than others. Although other malfunctions may occur, and the device itself does not always show a specific code. If you are not sure, it is better not to take risks so as not to break the device. In difficult cases, you need to study the warranty obligations and call the service center.