TOP 5 reasons why the washing machine does not wring out the laundry. Do-it-yourself washing machine repair - Setafi

When the washing machine does not spin, this does not necessarily indicate a breakdown. For example, a mode with a decrease in speed or no spin at all (for clothes made of delicate fabrics) can be selected. But often there are more serious cases when repairs are required. Top 5 main causes, as well as additional cases of breakdown and step-by-step instructions for its elimination are discussed in this material.

Blockage in the drain system

A very common case is when the machine does not wring out the laundry due to blockages in the drain system. During operation, fluff, dust and other particles get stuck in different parts of the unit. In this case, various elements may suffer:

• pipe branch;
• a filter that purifies the waste liquid;
• pump;
• a hose through which water flows to the sewer;
• the place where the machine is connected to the sewer pipe.

The main symptom of a malfunction is that water leaves too slowly or is completely in the tank. To determine the specific case why the washing machine does not wring out, it is necessary to disassemble each part step by step and inspect it, then rinse it under running water. Make a replacement if necessary.

The step by step instructions are:

1. Switch off the power supply and close the valve.
2. Unscrew the fastening of the drain hose, drain the remaining liquid into a pre-prepared basin. Rinse it under water.
3. Feel the pipe, find the place of clogging. Loosen the clamp and remove the pipe from the pump.
4. Remove the bolts and wires, then remove the pump and also clean it.
5. Next, you need to completely dismantle the pipe at the point of attachment to the tank. It is also cleaned by hand. If after that the washing machine does not wring out, it remains only to inspect the junction with the sewer pipe and, if necessary, remove the blockage. Then carry out a test wash in fast mode and check how the device works.

The simplest reasons

If the washing machine does not spin, the reasons can be very simple. In order not to call the wizard and not contact the service center, it is recommended to conduct an independent diagnosis according to the following plan:

1. You may have selected an operating mode that does not include spinning. It is used for processing special fabrics, such as woolen or silk. This explains why the washing machine does not wring out the laundry.
2. One more case is connected with elementary overload. It is clear why the machine does not wring out a large amount of clothes - it is difficult for the drum to rotate, and it cannot accelerate to the desired speed. In such cases, it is better to distribute all things over 2 cycles.
3. It also happens that the LG washing machine does not wring out clothes due to overall items. For example, a blanket, duvet cover or heavy coat is tangled up in one lump, and again it is difficult for the drum to rotate. It is necessary to evenly distribute and start the process again.
4. In some devices, a reduction in speed is provided during the spin cycle. And if you activate this function, it is easy to explain why the washing machine does not wring out the clothes to the end, as in normal operation.

Drive belt breakage

If the washing machine has stopped spinning, the cause may be a broken drive belt. Some models have a belt that is very tight between the drum and the engine. It can wear out and even break. In the latter case, the drum will completely stop rotating.

If the repair has not been carried out for a long time, and the washing machine does not wring out the laundry, it is recommended to replace the old belt, rather than trying to tighten the old one. Do this in case of a decrease in speed or the cessation of rotation of the drum. The sequence is:

1. The unit is de-energized, the valve is closed and a basin is prepared in case of leakage of liquid from the intake hose, which must be unscrewed and all residues drained.
2. Using a Phillips screwdriver, remove each bolt from the back panel and find the belt. They inspect it - if everything is in order, pull it tightly onto the pulley so that it is tight, like a string. This will require quite a lot of effort. It is necessary to act with two hands - one pulls the belt, the other at the same time scrolls the pulley.
3. If the belt is too old and the washing machine has stopped spinning, all that remains is to remove it and put on a new one.
4. Then a test wash is run to check how well the device works.

Broken sensor

In any model there is a special device that takes into account the number of revolutions - it is called a tachometer. If the part fails, the drum will not be able to rotate at sufficient speed. Then it is easy to understand why the washing machine does not wring out.

The main symptom is that the drum has stopped spinning or rotates rather weakly. As a rule, the tachometer is not repaired, but simply put a new one according to the following instructions:

1. The unit is de-energized, the valve is closed, the hose is disconnected and water is poured into the container. Turn back side.
2. Unscrew all the bolts and remove the back panel. This is necessary in order to understand the reasons why the washing machine does not wring out, as well as to carry out repairs.
3. Now remove the rotor and stator. To do this, use heads 17 and 10, respectively.
4. Examine the tachometer. If the reason is clear, because of which the washing machine does not wring out, the part is replaced with a new one. Buy the exact same part.
5. Then collect all the elements, acting in reverse order.

Control unit failure

When the machine does not wring out the laundry, the reasons can also be looked for in the control module, that is, the board with the processor. It should be understood that electronics are sensitive to voltage drops. If a jump has recently occurred, the washer should be disconnected for 15 minutes from the network, and then turned on again and check how it works.

But what to do if the LG washing machine still does not wring out is easy to understand. You will have to remove the front panel and remove the board. Perhaps she suffered not only from the drop, but also from the high humidity of the air, drops that fell on her. Then you need to check each contact with a multimeter and, if necessary, solder it.

If the washing machine does not wring out the laundry, and the reason is connected precisely with the electronics, it is only allowed to repair the control module if you have the appropriate experience. If the unit freezes, programs go astray, it is better to entrust diagnostics and restoration work to an experienced specialist. He will understand why the automatic machine does not wring out and fix the problem.

Shock absorber wear

When the washer does not wring out, this can also happen due to the wear of the shock absorbers. The main features are:

• strong vibrations during acceleration of the drum;
• extraneous knocks from the inside (the drum beats against the body);
• the machine has stopped pressing or does it too badly.

It is easy to understand what is the reason that the washer does not wring out. But replacing shock absorbers is more difficult, since it is a laborious task. The sequence of actions is as follows:

1. If we talk about what to do in the first place, if the washing machine does not wring out, you need to remove the top cover by unscrewing each bolt.
2. Remove the tray into which the detergent is poured, remove the panel from below.
3. Remove the cuff, after dismantling the clamp. This will help to figure out why the washer does not wring out.
4. Unscrew the fasteners, remove the front panel and dismantle the lock that closes the door.
5. Next, shock absorbers are found in the lower part from the sides. It is because of their wear that the washing machine does not squeeze out. Push the latches, take out the old parts and replace them with new ones. Do all steps in reverse order.

In most cases, it is easy to figure out why the machine does not wring out the laundry. But self-repair is not always possible. If there is no confidence in understanding the causes or the skill of restoration work, it is recommended to contact the master.