The washing machine freezes during washing

Weight Limitations

Each washing machine has certain characteristics. At the same time there are restrictions on weight. The technique allows you to wash at one time from 4 to 6 kilograms of linen. This figure depends on the model. If you exceed the recommended weight, the device may break. It is for this reason that many manufacturers install protection systems. They work at an overload. As a result, the washing machine stops.

To avoid such situations, you should carefully study the instructions and recommendations of the manufacturer. Do not exceed the weight specified in the documents. For the device to work, you need:

1. Drain.
2. Disconnect power.
3. Remove some of the contents from the drum.

The imbalance of laundry in the washing machine

Why does the washing machine stop during washing? There are many reasons for this. It is not necessary to turn off the washing machine due to breakage. Probably, protection works. In some models, sensors are provided that are triggered by an imbalance. This phenomenon occurs in cases where the laundry is accumulated on one side of the drum. This causes a strong vibration. Imbalance is no less dangerous for a washing machine than overload.

To avoid strong vibration, you should gently fold the laundry inside the appliance. If the washing machine stopped during operation, it should:

1. Drain.
2. Disconnect power.
3. Spread the contents of the drum evenly.

clogging of the water supply or discharge system. If the device stopped working in the “Rinse” or “Spin” mode, the cause of the malfunction lies in the clogging of the system that drains or supplies water. In such situations, protection also works. As a result, the drum stops rotating.

Clogging often occurs in a hose designed to drain water, or a pump. However, trash mainly accumulates in the filter. To fix the problem, inspect the hose. He should not bend over. If it is not clogged, the filter is clogged. This part is located inside the washing machine. First you need to drain the water, stop the device, remove the panel and remove the filter. Dirt, hair and small debris can accumulate here. The filter should be carefully cleaned and then inserted into place.

If the engine is broken

The engine is the heart of the washing machine. It is thanks to the engine of the drum unit starts to move. If this part has fallen into disrepair, the washing machine can stop at any time. It can be not only the washing process, but rinsing or spinning. A washing machine can get water and stop.

In addition, the engine failure also indicates that the device’s drum does not rotate, although the washing machine functions normally. Eliminate a similar fault on their own not work. For this you need to seek help from a specialist. The service will conduct a complete testing of systems, and then repair all faults. As a rule, the engine of the washing machine simply changes to a new one.

Malfunction of the heating element( heating elements)

The heating element is another important element of the washing machine. If the heating element breaks down, the unit cannot function normally. In other words, the water stops heating. Because of this, the washing machine can stop during striking or spinning. You can determine the damage before the technique stops working. If a program with a high temperature is selected, the glass does not mist over and remains cold.

If the washing machine stopped during washing and the water does not heat up, then the reason lies in the breakdown of the heating element. In some situations, the heater may be in order. Perhaps one of the wires went away. They should be checked. This requires measurements with an ohmmeter. If the device shows an infinite resistance, the heating element is not working properly.

Replacing the heating element

The heating element is not repairable. It must be replaced. To do this, drain the water, turn off the power, remove the cover located behind the washing machine, and disconnect the sensors, ground, and power cord. The screw nut should be loosened. To do this, you need to make about 6 turns, and then press in the screw. Having performed these actions, you can easily remove the heating element.

When choosing a new heating element, special attention should be paid to labeling. Each model requires its own heating element. To enter the heater in the grooves should be evenly and without distortions. Hardware should be twisted with effort. However, they are not worth dragging. At the end of the installation it is necessary to connect all the wires. Then you need to replace the cover of the device, and run a test program at a high temperature. If the device does not freeze and works normally, then the problem is eliminated.

Sensor failures

If the device starts a normal cycle, but suddenly hangs or shuts down, then this could be caused by sensor failures.

• laundry balance sensor;
• speed sensor;
• pressure switch( water level sensor);
• temperature sensor.

They are used to control all major processes at each stage of the cycle. If one of the sensors is faulty, then it starts to transmit incorrect information. As a result, the washing machine may freeze, since the control unit cannot understand what temperature indicator, water level, and so on at the moment. The device can stop during rinsing, washing or spinning.

Contact your service center for troubleshooting. Here, experts will test and identify the damaged item. After that, the sensor is simply replaced.

Problems with the electronic control unit of the washing machine

The control unit is an important unit of the appliance. However, it can fail. Breakage can be caused by strong vibration, high humidity or voltage drops in the power grid. The control unit is the brain of the washing machine. It is he who collects all the information from the sensors, and also controls the components of the washing machine. If the equipment does not function correctly, it starts to hang or stop on rinsing or spinning.

If the control unit is malfunctioning, then it is impossible to repair the washing machine at home. A washing machine with such a breakdown should be taken to a service center, as there is special equipment to determine the fault. If the breakdown cannot be repaired, the control unit is replaced.

How to identify a malfunction

With many violations in the work of the machine may stop or hang in the process of washing. If the device has a display, then you should pay attention to it. Most often, an indicator with an error code is lit on it. This allows you to determine in which node the failure occurred. The manual of the washing machine provides a complete list of error codes.

If the washing machine gets water and then stops, then you should disconnect the washing machine from the network. After some time, you can turn on the device again. Perhaps an error occurred in the program management. Turning off the device from the network allows you to eliminate it. If it is not possible to eliminate the malfunction in this way, then you should contact the specialists. After all, a washing machine is not the cheapest equipment. In addition, to carry out repairs at home is not always possible.