Códigos de erro máquina de lavar roupa Miele

instagram viewer

Error code	What does	mean Causes of	How to remedy the situation
F01	The drying temperature sensor is faulty.	The thermistor, which controls the drying temperature, has failed due to a short circuit.	Inspection and replacement of the temperature sensor in case of malfunction. Checking contacts and wiring. Repair damaged areas.
F02 F03 F04	An error means that a problem has occurred with the drying temperature sensor.	Why the code is on the CMA board: Disconnection of sensor connections. Thermal sensor breakage.	To reset the error: All contacts between the thermal sensor and the module are tested. Thermistor is replaced with a serviceable part.
F10	There was a problem during the water flood.	Causes: There is no water in the system, or the inlet valve is blocked. Clogged water intake hose, inlet filter. Problems with the main module.	To solve the problem, do this: Unscrew the gate valve. Remove and clean the intake hose and the strainer between it and the valve. Diagnostics of the electronic board.
F11	There is no water drain.	For what reasons the code was highlighted on the screen: Low pressure in the water supply system. Pump filter, drain pipe or pump clogged.	How can I clear the error: The pressure in the water pipe is checked. Clean the filter, pipe and drain pump.
F15	Hot water intake.	Check if the connection is correct. Shut off hot water.
F16	Too much foam.	Dose of detergent exceeded. Water does not drain well.	What to do: In the future, reduce the dose of powder. Check the drain pump and nozzle for blockage. To remove the foam, turn on the rinsing mode.
F19	Water sensor malfunction.	Inspection Sensor. It is possible to hit a small object.
F20	Fault in the heating system.	Why did the Miele washing machine show the error code: Breakdown of the heating element( heating element). Thermal sensor malfunction.	How to fix the situation: Replace the heater. Install a new thermal sensor.
F29	Failure of the drying heater.	TEN drying does not work.	Replacing the heating element.
F34	The hatch does not close tightly.	Why the washing machine gives an error: The mechanical parts of the door were worn out: lock, tongue, handle. Breakage of the electronic lock of the hatch( UBL).	How to repair a Miele washing machine: Replacing broken door elements. Installing a new locking device.
F35	Unable to open the hatch door.	What happened: There was a blockage in the lock hole. Defective elements of the control board.	The door is being opened. The keyhole is then inspected and cleaned. Repairing electronic board.
F39 F41 F43 F45 F50	Electronics malfunction. Problems with the control module.	Change or repair of the main unit.
F46	Incorrect connection of the display.	Contact break or control board failure.	Repair and change items.
F47	There were problems with the BAE / SLT interface.
F48	There were problems with the SLT interface.
F51	The pressure switch is faulty.	Pressure switch failure.	Install the serviceable item.
F53	Speed sensor out of order.	Sensor breakage.	Replace Item.
F55	Incorrect operation of the CMA time control element.	Change parts.
F56	Reduced speed( do not reach 400 rpm).	Probably broken engine tachometer.	Checking the winding and the tachometer itself.
F62	Mode selector does not work.	Installing a new selector.
F63	Problems with the operation of the system that controls the trajectory of water.	Inspection and repair of the system.
F64	Trajectory sensor failed.	Sensor change.
F65	Defective lights in the drum.
F81	Drying unit does not work.	Replace the drying unit on the CMA Mile.
F83	Drying temperature exceeded the norm.	The thermistor may have broken.	Thermistor and Heater Check.
F92	Chances of losing a washer fungus are high.
F93	Breakdown of the additional unit relay.	Repair, change of relay.
F96	An alternative water supply is not included.	Check Items.
F100	Disconnected from IK6.

Over time, parts of the Miele washing machine wear out, unforeseen breakdowns occur. How to extend the life of the washer? Repair or replace defective items.

Self-diagnosis of the machine will help determine which element of the SM has failed. If a fault is detected, it immediately shows the error code on the display. Be careful - and you will understand how to fix the damage with your own hands.