Atlant is a modern automatic machine equipped with a self-diagnosis system. When something goes wrong, the corresponding information is displayed. If the machine has stopped working, you just need to look at the message on the display, check it with the instructions, and fix the problem.
Content:
- How to identify a malfunction by code
- How to fix the malfunction?
- What to do so that breakdowns occur as rarely as possible?
How to identify a malfunction by code
For each problem, the developers have provided a special code with which washing machines inform the owner about the nature of the malfunction. If your machine has stopped working and mysterious letters appear on the display, it's time to look into the technical documentation to understand what’s the matter. If you have lost the instruction, then the error codes can be found in the list below:
- Sel signals problems with the choice of work programs;
- None: There is too much foam in the drum, which complicates the operation of the machine;
- door says that the hatch lock is defective;
- F2: defective temperature sensor;
- F3: indicates a failure of the heater;
- F4: the drain pump does not work;
- F5: faulty filling valve;
- F6: reverse relay does not work;
- F7: mismatch of power supply network parameters;
- F8: tank is full;
- F9: defective tachogenerator;
- F10: problems with loading door lock;
- F12: engine malfunction;
- F13: a problem allegedly caused by an open circuit;
- F14: malfunctioning software;
- F15: There was a leak in the device.
How to fix the malfunction?
After the nature of the malfunction of the Atlant washing machine has become known, it should be eliminated. It happens that the machine just freezes. Most often, this problem occurs due to minor software failures and is easily fixed by rebooting the machine.
If the equipment refuses to work, and a trouble code appears on the display, proceed as follows:
In case of problems with the software sector, the presence of which the code saysSel», You should check the operating status of the selector and controller itself.
If there is excess foam in the drum, and the inscription “None", First of all, you need to understand why this happened. Otherwise, after the elimination of the error, you run the risk of colliding with it again, re-creating the emergency. As a rule, too much foam appears due to the use of detergents in larger quantities than required. In this case, you just need to put less powder in the appropriate compartment.
It happens that the powder creates too much foam, although you clearly followed the instructions on its packaging. Some powders are not intended for use in modern automatic machines. They create too much foam. To avoid this, do not save on quality detergents and before use make sure that the powder is suitable for an automatic washing machine. Avoid using handwash products.
Excess foam is not always associated with the powder. Washing machines can also fail if the wrong washing mode is selected, which does not correspond to the type of fabric and leads to the formation of foam in large quantities.
Once you understand the reason, just turn off the machine, drain the water, remove items, rinse the drum and start the wash again without repeating your mistakes.
If on the display of the Atlant machine you see a message about a malfunction of the temperature sensor ("F2»), Make sure that the electrical circuit is working and the information displayed is correct. If there are no breaks in the circuit and the sensor is really defective, it should be replaced.
The cause of the failure of the heater ("F3»), As a rule, is a breakdown of the heater, or an incorrect signal due to an open circuit. When this error appears on the display, both the control module and the electrical circuits are checked. If everything works, the cause is a violation of the integrity of the heater.
The drain pump fails (“F4») Due to obstruction of the drain system. Clean the pump and filter.
If the code “On” appears on the display of the Atlant washing machineF5", Then the inlet valve is not working. It is necessary to clean the intake system, clean the strainer. It is also important to make sure that the water comes under sufficient pressure and that the water supply tap is working. If this error occurs, they diagnose the solenoid valve and its connections to the mains.
If there is a problem with the relay ("F6»), Then check the relay and, in case of a malfunction, replace it. A relay malfunction also serves as a signal to check the operation of the engine of the machine.
Power problems ("F7»), If the voltage meets the requirements of the washing machine, and the socket works normally, they arise due to a malfunction of the interference filter or the control module.
An overfilled tank will break ("F8”) When the water inlet valve is stuck in the open position. If the valve functions stably, it means that the cylinder is not tight, or there is a malfunction in the pressure switch or control module.
Failure of the tachogenerator ("F9») Requires replacement of this item. Also, when this code appears on the display, you need to diagnose the engine, the control module.
If the electronic lock does not work (“F10»), Pay attention to the operation of the lock itself and the electronic module, the cause of the breakdown, most likely, lies precisely in them.
If the hatch (“F11»), Then you need to make sure that it is in the correct position, check the electronic module and electronic lock.
In case of engine failure ("F12») Check the motor winding, the motor itself and the control module. If the engine is broken, it must be replaced.
Code "F13”Indicates that the washing machine finds it difficult to determine the cause of the malfunction. You need to make sure the integrity of the contacts and modules.
Error with code "F14»Signals the need to change the electronic module.
If a leak occurs ("F15»), You need to inspect the boot hatch cuff for damage. Leakage may also occur in the drainage system or in the tank.
Read also:
- Replacing the pump in the washing machine: instructions with photos and video examples.
- Ardo washing machine malfunctions: reasons and description.
- Washer Combustion: malfunctions and their diagnosis using the error code are described here: https://sovetexpert.ru/neispravnosti-stiralnoj-mashiny-gorenie.html
What to do so that breakdowns occur as rarely as possible?
Damage to the washing machine is an unpleasant situation, to put it mildly. No one wants to wash by hand or carry kilograms of laundry in the laundry room. In order for your Atlant, an automatic type washing machine, to work for a long time and not need the help of repair service employees, it is worth observing some simple rules for operating the equipment:
- Follow the rules for using the equipment described in the technical documentation that came with the machine.
- If the washing machine works all day, washing one batch of laundry after another, a break of 1-2 hours should be taken between washings.
- Carry out antifungal prophylaxis of internal surfaces, if necessary, treat the affected areas with special means.
- Use high-quality detergents, as well as special compounds for cleaning the washing machine and descaling. If the water is too hard, add a softener to the laundry detergent with each wash.
In the video below, the man talks in detail about how to independently fix most of the small problems that periodically arise during operation of the washing machine. After watching the video, you can not only clean the filter yourself or powder compartment, but also perform simple operations to replace the electronics.
The times when domestic-made washing machines were inferior as foreign counterparts are a thing of the past. Modern Atlant machines with a built-in self-diagnosis system promptly inform the user about problems, allowing you to independently monitor the condition of the equipment.
In contact with
Google+
Classmates
