How to get rid of the gaps between the bathroom and the wall without the help of a master in just 2 days

click fraud protection

Content

  • 1 Surface preparation
  • 2 Sealing method
  • 3 Decor

When installing the latter, a gap often appears between the wall and the bathroom, and it can even be in cases where the surface is perfectly smooth, not to mention any differences. In this case, after installation it will be necessary not only to wipe all the seams, but also to get rid of the hated gaps, which not only look absolutely unpresentable, it also causes a lot of problems during hygiene procedures, moreover, they are capable of causing more significant over time Problems.

/

It is far from always necessary to call a master and pay for his services, because you can do everything yourself, this does not require any special skills and knowledge.

/

Surface preparation

In many ways, the method of sealing the joint will depend on the size of the gap. All contaminants, paint should be removed from the surfaces, then the wall is thoroughly washed and dried. The next stage is the treatment with special antifungal agents. In the event that the width between the bathroom and the wall is more than 3 cm, then it is best to place the gap fasten the profile or strip, they will become a solid foundation for the finishing coat used in the future material.

instagram viewer

/

Sealing method

The simplest and most frequently used method is to use it for cement mortar, but it is better to dilute it with water and PVA glue, the quality of the seam will be ideal.

/

When the gap width is up to 5 mm, the solution is carefully applied with a spatula, remember that the solution will quickly harden, therefore it is better to smooth its surface immediately. It is better to engage in further decor after two days, after complete drying.

/

Often, a waterproof waterproof foam is used to close the seam, it will provide the best adhesion to the surfaces. Thanks to this method, even for especially large slots, it is not necessary to use a profile. After applying the foam after an hour, its excess is carefully cut with a construction knife, the surface is treated with silicone.

/

Decor

The most budgetary, and therefore especially widespread version of the decor is the use of a plastic corner, it allows you to hide all defects and irregularities during rough grouting with cement or foam. You can attach such a baseboard to the surface using transparent silicone glue, it will also act as an antimicrobial agent, which is very important for rooms with high humidity.

/
/
/
  • 3 easy ways to make a finnish candle3 easy ways to make a finnish candle
  • A quick way to install postsA quick way to install posts
  • Without which tool it will not work to make a hole in polycarbonateWithout which tool it will not work to make a hole in polycarbonate
  • What is the best waterproofing of a bathroom under a tile?What is the best waterproofing of a bathroom under a tile?
  • DIY plastic bottle tubesDIY plastic bottle tubes
  • Options for protecting pipes from freezing in a country houseOptions for protecting pipes from freezing in a country house
  • The doorbell rings from an old cell phoneThe doorbell rings from an old cell phone
  • What material is suitable for painting OSB plates on the facadeWhat material is suitable for painting OSB plates on the facade
  • How easy it is to update a kitchen apron without knocking down old tilesHow easy it is to update a kitchen apron without knocking down old tiles
  • How to arrange the supply ventilationHow to arrange the supply ventilation
  • How to install platbands on a door without nailsHow to install platbands on a door without nails
  • Why you should not do dry cutting tilesWhy you should not do dry cutting tiles

New publications are published daily on our channel in Yandex. Zen

Go to Yandex. Zen/
Simple inverter without transistors

Simple inverter without transistorsWith Your Own Hands

To create a simple inverter without using transistors, you only need a couple of parts. It will convert DC 12V to AC 220V. And most importantly, all components can be easily found and installation...

Read More
An easy way to make an ice rink at home

An easy way to make an ice rink at homeWith Your Own Hands

Content 1 Weather requirements 2 Preparing the site for the rink 3 How to fill in water 4 Ice painting The ice rink is one of those places where you can plunge into the atmosphere of a fairy t...

Read More
Laminate grooves split: how to fix without re-laying

Laminate grooves split: how to fix without re-layingWith Your Own Hands

During the repair process in the room, the owner often encounters difficulties, and they can be completely at any stage of the work. Many people independently do everything in order to save money,...

Read More
Instagram story viewer