Installing the water heater with your hands

click fraud protection

Water heater - a device frequently used in private homes with independent water supply. Also it is used as a backup source of hot water in apartments, when it centralized supply for any reason suspend.

Process of installation accumulative electric heater

The content of the article

  • Process of installation accumulative electric heater
  • How to install water heater with your hands
    • Selecting a location
    • Installing and fixing
    • Connecting to the Communications

Installing of water heaterStorage water heaters or boilers are vertical, horizontal, upper and lower connection to the water supply pipes. Models with the upper connection suitable for installation under the sink.

Installing the water heater with the supply pipe to the bottom of the case is made from the top. It involves several steps. It begins with the definition of the place of installation, and ending with his connection to communications and the launch of the work.

How to install water heater with your hands

Installing the water heater ownHow to install a storage electric water heater? To get started, you need to choose where it will be installed.

instagram viewer

Place of installation depends on many factors that affect the choice of a particular model. To perform operational and quality of installation is necessary to prepare the appropriate tools and supplies.

Selecting a location

Choosing a place for the water heaterHow to install water heater? set point is determined depending on how much and what kind of users is planned to provide hot water.

If you plan to connect the charger to the shower or sink, it makes sense to place a small boiler in the vicinity of these points of analysis.

In the case of the need for a backup power DHW all consumers connected to the riser, it is necessary to look in the vicinity of the installation location of hot and cold lines.

Important! When choosing a place should be given to the support structure walls, which is planned to fix the unit. Hang heaters on plasterboard or plywood wall above head height is strictly prohibited, and is life-threatening.

In the case of a floor fixing is necessary to provide a small space around the unit for service opportunities.

How to connect the water heater to the mains? Biphasic device is allowed to include in conventional electrical outlets, subject to availability in their ground and their readiness to take the load of the device.

Once you have decided on the spot and convinced of its suitability for installation, it is possible to sum communication.

Installing and fixing

Installing of water heaterHow to connect a water heater? For mounting you will need:

  • Level;
  • Puncher with pobeditovym drill or drill - for mounting on a wooden wall;
  • Set of screws with plugs for fixing the equipment on which hung boiler;
  • Powerful screwdriver or screwdriver.

Installing the water heater is made in stages. Or snap fastening are attached to the wall and positioned horizontally via level. Distortions in fastening highly undesirable because they can lead to uneven distribution of the load and the disruption of the tank filled with water from the support surface downward.

Next, a pencil or marker shows holes locations on the wall. Drilling must be to a depth of a couple of millimeters greater than the length of the dowel. Recent deepened into the wall with a hammer with a rubber tip.

Fastening fixed in the prepared hole diameter suitable for screws. Top drive is suspended, and if necessary, it is also fixed in one or several places on the wall, depending on the model.

Connecting to the Communications

Connect the water heaterTo connect to the summed plumbing fittings, ending fittings you need to prepare:

  • A pair of movable keys;
  • Fumlentu (sometimes use tow with sealing paste);
  • gaskets;
  • Flexible hoses;
  • Fitting.

Wiring water heater such: for convenience, the drain and immediately before the inlet nozzle apparatus installed tee. Its lateral outlet ball valve is screwed. Through its flexible bight can be connected to the sewage system or to the outlet nozzle.

Important! The free outlet check valve is installed, and then through the shut-off valve device is connected to the cold-water conduit.

Connection of the storage water heater with their hands is performed through the valve to the pipe with hot water. The joints of all structures shall be sealed with the seal or gasket.

After connecting the water heater, make sure there are no leaks. You can then switch on the device in the socket and to perform a test heating. If a pressure leak in the joints also appeared, boiler is ready for operation.

How to drain the water from the water heater - draining options

How to drain the water from the water heater - draining optionsWater Heaters

The modern market of household appliances are highly variable. Manufacturers regularly offer their customers new, advanced models of Bole. These are and water heaters. Correct operation and compli...

Read More
How to turn on the water heater: the first start of the boiler, instructions and important nuances

How to turn on the water heater: the first start of the boiler, instructions and important nuancesWater Heaters

Frequent interruptions in the work of utilities make users think about the need to provide their own housing with autonomous engineering networks. Regular shutdown of hot water supply is compensat...

Read More
The water heater does not turn on: causes, failure detection

The water heater does not turn on: causes, failure detectionWater Heaters

Damage to the water heater can cause a headache for its owners, if the device is installed in the country, and calling the master is difficult or very expensive. Dismantling and transporting the d...

Read More
Instagram story viewer