How to remove the cartridge from the printer without damaging the device?

Nowadays, printers are used to print documents and files. These are special peripheral devices connected to a computer and converting information from an electronic format in a database to paper media. The operation of any printer is the sequential execution of a certain cycle. It consists of several main stages:

• Connecting equipment to a power source and recognition by a computer program.
• Setting the print format and the quality of the resulting display.
• Loading cartridge and paper, starting work.
• Sequential printing of pages of the document.

This happens with every use of the program. As can be seen from the described manipulation plan, one of the main elements for the implementation of the work is a cartridge. For normal printing, it is necessary to monitor its condition, the amount of ink... After it is completely consumed, it must be refilled or completely replaced with a new element.

How to remove the cartridge?

Before you begin to install a new element inside the printer, you must remove the old cartridge. To do this is quite simple, especially if you have experience with the technique. However, if this is your first time doing the manipulation, it’s best to follow the steps and carefully remove the cartridge from the printer. To do this, follow the instructions:

1. Prepare the workplace, remove excess jewelry from your hands and roll up your sleeves for convenience and to prevent ink from getting in.
2. Carefully lift the printer cover and look inside the case. During operation, some parts may become very hot, be careful when touching the elements.
3. Locate the cartridge, in some models it can be held by special clips. Gently pull them away without sudden movements so as not to break.
4. After loosening the clips, pull on the special handles or recesses on the cartridge. If it is stuck, contact a service center for help. Sharp and violent movements can damage the equipment.

When you open the case, the cartridges can continue to move for some time without ink, do not stop them yourself. Wait a while until the movement stops, then remove them.

IMPORTANT: Different versions of the equipment have their own characteristics when installing removable parts, for convenience it is worth reading the instructions and watching instructional videos.

The cartridge must be removed very carefully, as it contains many small parts, damage to which can adversely affect print quality.

How not to get dirty in paint?

An important point when replacing a cartridge is the presence of remaining ink in it. The problem is that the coloring composition inside the element can stain human skin and surrounding objects. In order to protect yourself and the elements of your home interior, use the following tips:

• Prepare the workplace, lay sheets of paper on the surface. Remove excess objects from the table.
• Put on an old apron or cover your body with a towel. Always wear gloves on your hands; you can use old knitwear that you have not used for a long time.
• Also stock up with rags or napkins to quickly remove paint on your skin or clothing. Store paint remover thinner when it dries.

IMPORTANT: Do not shake or turn the cartridge over to check the level of ink remaining, as this may result in ink leakage.

Of course, different types of paint or polymer powder (toner) have different effects and require special precautions. In some cases it will be useful to use personal protective equipment: rubber gloves, respirators, goggles.

How to refill a cartridge?

After you have deleted the old element, you can replace it with a new one, but to save money, you can use the gas station at home. It’s easy enough to do this even for a novice, but the first try may raise some questions. A step-by-step plan for performing the manipulation will help answer them:

1. Prepare the ink and syringe to insert it into the cartridge body.
2. Using a piston, fill the capacity of the syringe to the upper mark. Do not fill to the limit, otherwise the paint may spill.
3. After that, find the hole on the outer casing and insert the needle from the syringe into it. Start gently and smoothly pour the ink into the container, filling it.
4. Finally, seal all openings in the cartridge to prevent ink loss.

In the case of using toner for a laser printer, the process will be slightly different:

1. Prepare personal protective equipment as polymer powder is highly toxic.
2. Remove the item from the printer, inspect its walls. There should be a hole on the top cover. In its absence, it is required to burn a small hole in the wall.
3. Then, using a special funnel, pour the powder into a free chamber.
4. Then cover the hole with a plug or duct tape.
5. In some cases, it is necessary to apply a special chip to the cartridge (included) so that the computer and printer programs recognize it

This option is suitable when using universal technology and suitable coloring material for refueling. Some manufacturers limit the ability to work with non-native elements, it is worth considering this before you try to insert a refilled cartridge. Information can be found on the cartridge housing or in the printer manual.

IMPORTANT: Do not leave the printer for a long time without a cartridge; this can lead to a malfunction and poor print quality.

Therefore, it is recommended to quickly replace or refill the paint in order to quickly restore the equipment.

How to insert a cartridge?

After refueling, the easiest action remains, now you need to insert everything into its original places. To accomplish this, do the following:

1. Disconnect the needle and syringe, rinse them thoroughly until the ink is completely removed.
2. Place the cartridges on a flat surface with the holes facing up so that the ink inside them settles.
3. Now determine the previous location on the moving carriage. Turn off the printer so that the printheads do not move or interfere with the main process.
4. Pre-open the holes by removing the tapes or tape to cover them to allow paint to enter the nozzles.
5. Without sudden movements, insert the element inside the device until a distinctive click appears, indicating that the installation is correct. Do not push with force.
6. If there are locking clips, slide them slightly to carefully install all the components.

So you can definitely refill the cartridge or install new equipment if necessary. This will significantly save your money and time.

To improve performance and increase productivity, read more information about your equipment and use the tips:

• Diagnose and troubleshoot operating problems.
• Periodically clean structural elements from dust, dirt and foreign elements.
• When refilling cartridges do not mix different compositions, this spoils the printing machines.
• If the equipment does not support foreign parts, try not to use them.