How to clean the printer: what you need, step by step instructions

Almost everyone has a printer at home or uses it at work. Therefore, it is important to know and be able to properly clean it from paint and dust. What are the rules and how to clean a dried printer? About this and other below.

Printer Cleaning Rules

To clean the printer and not damage its components, you should follow these guidelines:

1. Do not use flammable solvents or aerosols in the process. This will cause a fire or electric shock.
2. Do not touch the fuser unit. He is hot. This can cause burns and print quality problems.
3. Do not touch the transport roller. Otherwise, it will be damaged and ruin the print quality.
4. Do not bring toner to your face or breathe vapors. It is life threatening.
5. Before you begin, disconnect the printer from the network. Otherwise, a fire or electric shock may result.
6. When cleaning the registration roller and paper receiving mechanism, do not press on the surface of the actuator. It may break.
instagram viewer
7. Do not pressurize all rollers due to possible loss of print quality.
8. Do not touch the tape with gloves or bare hands and do not expose it to light for more than 800 lux for 2 minutes. This will immediately damage its structure and damage the printer.
9. Do not touch the charging roller during the process, and do not use volatile liquids near its surface.
10. Do not use coarse abrasives to clean dustproof glass.
11. Do not wash the print head with ethanol or acid solutions. Despite the good effect of them, the nozzles in the device will not last long.
12. As a means for the process, use only special cleaners for the printer. They are sold at every electronics store.

Advice! In the absence of proper experience with the printer and knowledge of its device, you should entrust the work of cleaning its components to professionals. They will competently and quickly service the printer.

What you need to clean

To clean the print head of any printer, you should take:

1. plastic dishes (disposable plate or container for food);
2. dense rag or gauze;
3. special kit (sold in any electronics stores).

To clean other surfaces, you need to take a medical syringe, flushing fluid and medical gloves. To remove dust, you need a simple brush or slightly moistened disposable cloth. You will also need to put on things that will not be a pity to throw out in case of stains or an apron.

If the printer does not print well, it doesn’t matter if it is an inkjet or a laser, it is necessary to do deep cleaning.

How to clean the printer: step by step

To clean the printer, you need to carry out a number of simple, but time-consuming work:

1. First you need to disconnect the printer from the network, lift the cover and completely clean the rollers from dust with a dry cloth.
2. Then remove the toner cartridge and wipe it with a disposable cloth.
3. Then you should remove the dustproof glass and wipe it with a special cleaner and wipe it dry with a paper towel.
4. The last step will be to return to the place of all components in the order in which they were removed.

To clean the printing device on the bottom of the prepared plastic dishes, you need to lay the bandage in several layers or a cotton cloth, and then pour the washing liquid. Then, remove the print head from the disconnected printer and place it in the liquid container with the ink compartments down. To put on a tube on the receiving nipple devices and previously to remove linings. After removing the gaskets, rinse them well in a liquid and dry. Then pour liquid into the tubes and leave them to wash for several hours. If necessary, it is worth adding solution to them.

If the liquid in the tubes does not evaporate, then they are very dirty and require a little more time for such a process. You can try to reduce the solution by force. To do this, take a syringe and draw out the liquid. In order not to break the tubes, you need to do this as carefully as possible.

To drain dirty liquid from plastic dishes, you need to remove the bandage and repeat the procedure for filling containers with liquid and lowering the printing device into it. The washing stages must be performed until the substance completely leaves the device. After work, you should dry everything for a couple of hours, fill in new ink, paste in the right places and check the print.

Tips:

• To carry out such a process from the outside, wipe it with a damp cloth.
• For the compressor, any micro-vacuum cleaner with a thin nozzle is suitable.
• To remove dust and powder, use cotton swabs or a newspaper. It is important to wear a respirator and latex gloves.

How to clean a dried printer

To clean a dried printer, you need to first completely remove it from dust with appropriate disposable wipes and brushes, as well as pull out the print head and restore it in the following ways:

1. Soaking in distilled water for 48 hours;
2. Boiling in boiling water for 1-2 minutes with repeating the procedure every hour until the desired effect is obtained;
3. Steaming by steam for 2-4 hours until the device is completely empty from old dried paints;
4. Soaking under streams of jets of hot water until the inks of the printing mechanism are completely softened and washed out;
5. Clean the cartridge with detergent for dishes and water.

The last way you can quickly clean the color cartridge. In previous cases, you can clean the mechanism only for regular printing.

In general, the printer must be cleaned regularly according to the rules above. This will not only preserve print quality, but also extend the life of the device. In the absence of the necessary knowledge with the skills of using the printer, it is worth giving the job of cleaning it to the hands of professionals.