DIY earbuds for headphones: step by step

For high-quality sound of music in the headphones used ear pads. This device protects the device from extraneous noise.

Ear Pads

The ear pads during operation quickly lose their original, factory appearance: they are wiped, torn. It’s not easy to find them on sale, so it’s easier to make protective nozzles yourself, which will emphasize your unique taste and style.

Material selection

If in the factory version the ear pads were made of foam, it is recommended to use the same material as a filler.

Helpful information! For new linings to last a long time, choose a foam rubber of dense structure.

Knitted ear pads look unusual. For craftswomen to knit such devices with a hook will not be difficult. Threads for knitted nozzles are recommended to use cotton or acrylic.

A simple attribute used to repair ear pads is wide terry elastic bands for hair. They serve as protective nozzles for a long time, do not slide off the headphones.

If you don’t know how to use a crochet, buy knitted socks. The elastic from them is perfect for ear pads. Socks are better to use new, unstretched, with a thick yarn.

Knitwear can be replaced with knitted or velor ones. Such fabrics are pleasant to the touch, do not cause irritation.

If the ear pads were originally leather, the replacement material is taken as similar to the original as possible.

Advice! So that new nozzles are used for a long time, choose good quality skin. Savings in this case are inappropriate.

Dermatine nozzles are hard to the touch, isolate extraneous sounds worse than their natural counterparts.

Depending on the density of the selected skin, foam rubber is selected. If the material is thin, it is advisable to take a rigid polyurethane filler. For thick leather fabric, in contrast, foam is recommended to use a more airy one.

If vacuum headphones are torn, you can easily repair them with your own hands. To do this, you need ordinary earplugs.

How to take measurements

Using a ruler, determine the diameter of the headphones. Then draw a pattern with a compass on a cardboard.

Helpful information! For large and small circles, leave reserves of approximately 2-3 mm from each edge. If the product is planned to be made of leather, it is recommended to make more allowances (about 4-5 mm).

Cut out the resulting cardboard template. Using chalk, transfer it to the back of the fabric. The result should be 4 rings (2 for each ear cushion).

DIY earbuds for headphones: step by step

Before you start creating original, stylish nozzles, the following items should be ready:

• The cloth.
• Foam rubber. Can be used from old nozzles.
• Thread, needle.

Attention! A sponge for dishes is not suitable for these purposes, since it does not allow enough air to pass through.

If the house has a sewing machine, the sewing process is greatly simplified and accelerated.

The step-by-step instructions are as follows:

1. The rings are displaced with each other on the wrong side out. Advice! To make it easier to sew, fix them with tape or clothespin.
2. Sew the ring first to a smaller diameter. The stitches should be small so that there are no gaps on the front side. If you own a sewing machine, use it.
3. If you retreated a little more from the edge than was calculated, that's okay. Just gently cut off the excess, so the workpiece will be easier to turn out.
4. To add volume to the ear pads, you need to cut a strip of fabric. Its width is determined by the thickness of the future product. Here it is also necessary to make a margin of several mm (up to 5). The length of the strip is approximately 25 cm.
5. Next, the strip is sewn along the edge of one ring. You need to leave an allowance of about 1 cm.
6. The next step is to insert foam rubber. Carefully thread the fabric blank into the polyurethane foam ring. The thickness of the foam should be the same as the planned ear cushion.
7. The final seam will be on the outside. In the process of connecting the strip with the second ring, do not touch the foam.
8. After the ring is sewn in a circle, you need to mash the resulting ear cushion. Such a simple technique allows you to evenly distribute the foam over a stitched structure.

To give the edges a neat appearance, they can be sheathed with decorative tape.

Attention! If the headphones are equipped with a side, then an extra ring must first be sewn to the ear cushions. With it, a stitched product will be attached to the music headset. Only after that the design is sheathed with decorative tape.

Similar manipulations are done with the second ring. The final stage of the life hack is attaching homemade pads to the headphones. For these purposes, you can use double-sided tape. For the best coupling of the nozzles with the headset body, take liquid glue.

We conclude: it is not difficult to make ear pads with your own hands. If you have free time, you can create an original stylish thing that will allow you to comfortably listen to your favorite music.