How to extend the drain hose of a washing machine - description

Today, having a washing machine at home will not surprise anyone. It would seem that it might be easier to connect this household appliance.

But when you install it on a pre-planned and prepared place, a simple, but at the same time unpleasant the problem is that the length of the drain hose that comes with the machine is not always enough to connect to the sewer hole.

How to extend the drain hose

There are several ways to get out of this situation. - you can purchase a new hose that will be suitable in size to solve this problem and completely replace it, or buy a modular pipe of the desired length.

There are two criteria for selection: the cost of materials and the complexity of installation. In the first method, you need to consider the individual device of the machine, since in some models the complexity of installation may depend on the design of the drain hose connection, because of which sometimes you have to remove the back panel of the household technicians.

It must be borne in mind that when dismantling the panels of the machine, which is under official warranty service, it can be damaged marked seals, as a result of which it will no longer be subject to further repair under the manufacturer’s warranty or seller.

It is important to consider the distance from the equipment to the drain of the sewer, the laid hose should not have sharp differences in height and sharp corners at the bends. He should just lie down, smoothly bend around all obstacles, not be in a tense state, be in a plumbing box, under a bathtub or in a place where he is not accidentally deformed.

When leaving the washing machine, the height of the drain sleeve should not exceed one meter - this makes it difficult to drain dirty water, and in the future it can negatively affect the operation of the pump, up to its breakdown.

To connect the drain modular corrugation, you will need to purchase a plastic connector and clamps the right diameter, which can be bought at almost any hardware store or car shop spare parts. For work, you need only a screwdriver, suitable for the slots, or a screwdriver with a set of bit bits.

In order to make a connection with your own hands, you need time and a small amount of tool. The modular corrugation is measured according to the required dimensions, then a plastic connector is inserted into both hoses, which is crimped on both sides with clamps.

If the drain hose is completely replaced, carefully read the supplied washing machine manual if you need to remove the back cover. Pay attention to the presence of seals, determine whether it can be removed without danger of violating warranty markers, or you can trust the competent specialists in this field of services, but whose work will have to pay.

Therefore, the owner decides for himself - to do everything himself, or, due to lack of time, lack of desire, will rely on plumbers.

Attention! Before starting work, you must first disconnect the machine from the mains and shut off the water supply. Observing these simple safety rules, you protect yourself from possible injuries and prevent premature failure of your household appliance.

As a result of these manipulations, the following snag may occur - lack of length of the water supply hose to the washing machine. But this problem is solved in a manner similar to the previous one.

The only caveat - This is a purchase not of a plastic nipple, but of brass, with a diameter of 20 mm with an external thread for the connecting nuts of two hoses. At the same time, only the muscular strength of the hands will be required for the work, due to the fact that the design of the union nuts is made of plastic, and excessive applied force to twist them, can lead to deformation, and in the future and licking of the internal thread products. If it is not possible to tighten them tight enough or they are not comfortable for work place, use the open-end wrench of the right size, while controlling the supplied efforts.

Water hose replacement

You can also completely replace the water supply hose to the washing machine by purchasing a ready-made pipe of the required length. Unlike a complete drain hose replacement, there is no need to disassemble a third of the washing machine, since the locknut with rubber seal / external thread (depending on the model of household appliances) at the water inlet is on the rear wall cars.

Reference! In order not to fall into such situations in the future, you need to select the equipment and its location as accurately as possible. If your bathroom, kitchen, utility room in which the machine will be located, is under repair, then you need to take care in advance for plumbers to lay water supply, sewerage, outlets of water outlets (the height of the inlet / outlet must comply with building codes and rules, otherwise it threatens further formation of blockages in drain pipes) according to a pre-compiled plan which will take into account the further comfortable location of plumbing, household appliances and furniture.

As you can see, having analyzed the article written above, there is nothing complicated in lengthening the drain / feed hose of the washing machine, and even a fragile housewife can cope with this task.