How to remove a stretch ceiling: process technology depending on the type of fastening

High quality stretch fabric can last up to 20 years. But it may be necessary to dismantle it. For example, if the neighbors are flooded and you need to remove the water. There are several methods for removing a stretch ceiling, depending on the features of the attachment. It is worth studying all the nuances of the procedure.

What you need to know about stretch ceilings before removing

Dismantling can be done by hand. You just need to decide what exactly the procedure is required for. Sometimes it is not necessary to remove the entire canvas, it is enough to remove only a part.

Reference. Before dismantling, you should find out what type of construction and fastening was used. The choice of coating removal technology depends on this.

If the reason for such work is a flood, then first they get rid of the water. It is enough to remove any ceiling lamp and drain excess liquid through the resulting hole. Another way is to gently fold back the corner and drain into a bucket.

Dismantling a stretch ceiling

The process consists of several stages. Preparation is imperative. Then they act on the basis of the type of structure that was used for lining the ceiling.

Training

They start by vacating the premises. All items that can be taken out are removed. The rest, heavier ones, must be covered with a protective film. The room should be as spacious as possible. Removing lighting fixtures from the ceiling.

You will also need to prepare tools. It is more convenient to work on a ladder, otherwise it will be difficult to reach the desired area. You may need a heat gun, spatulas of various sizes, special clamps, which are convenient to hold the canvas. Additionally, take pliers and a screwdriver. You can also use a knife and duct tape.

Then they check how the web is attached to the structure, and proceed according to one of the suitable methods.

How to remove a stretch ceiling with a harpoon mount

This type is a flexible plastic strip. It got its name due to its external resemblance to a harpoon. In this case, you can dismantle it yourself. First, heat the vinyl with a heat gun. It is enough to set the temperature to 70 degrees. This will allow the material to become more flexible and pliable.

Important. Removal starts from the corner. You can only heat the area of ​​the surface from which the harpoon will be removed. Instead of a heat gun, it is permissible to use a hairdryer.

When dismantling, it is required to remove the harpoon from the protrusion, which is located inside the profile. Then the rest of the canvas is simply stretched. It is recommended to proceed as follows:

1. Heat the surface evenly starting from the central part and move towards the corners.
2. Find an area with a fairly large gap between the structure and the wall. This should not be the place where the butt-end gluing of the harpoon takes place, otherwise, with physical impact, the film will simply break.
3. Use a screwdriver to squeeze out the mount. A curved blade is pushed into the resulting space and a harpoon is hooked.
4. Then they begin to drive it in different directions to squeeze it from the baguette. Do the same on the perpendicular side. This will allow the harpoon to be hooked up with multiple blades.
5. Begin to pull the shoulder blades down, parallel to the wall. It is important not to use too much force or act harshly.

When the harpoon together with the film come out of the profile, you should move along the wall, parallel to carefully pulling the PVC. Clamps are recommended when working over a large area. This will prevent deformation and strong stretching of the film.

Reference. For small spaces, preheating can be omitted. But if the ceiling has a large area, then this process is required.

Dismantling the PVC ceiling with other types of fastening

In addition to the above, other types of fixation are used. The further course of work depends on this. There are the following types:

1. Shtapikovaya. Used for fabrics. Differs in high cost. The system is self-tightening. First, the baguette is fixed, then the corner of the canvas is fixed into it, leaving an allowance of several centimeters, and the tension is started. The structure is fixed with a glazing bead. It presses itself against the profile under the pressure of the web. For dismantling, you must first remove the glazing bead, then proceed with the careful removal of the product.
2. Cam. Also called clip-on. It is used for both woven and vinyl fabrics. The most popular type. It is widespread due to its affordable cost, ease of installation. It allows you to get a seamless canvas due to the fact that a minimum indentation is needed from the ceiling. The fastening resembles a self-clamping one. During installation, the web is stretched due to movable cams or clips. They also serve as a fastener for the material. Dismantling is carried out with a spatula. It is better if it is made of plastic in order to preserve the canvas. It is enough to squeeze it out with a spatula, remove it, then pull out the material. It is recommended to start work from the corner where the free end is. If he is not there, they are released on their own.
3. Wedge. Wedges, which serve as fasteners, are driven into the baguette during the installation phase. A ceiling plinth is used for tight clamping. It performs several functions, acquiring the role of a decorative element. This type is the easiest to dismantle. There is no need to pull the material. It is enough to remove the plinth from the structure. This will loosen the wedge. Then, using a spatula, the fasteners are pulled back. Take out a wedge, the canvas is removed.

Attention! Some types of fastening that involve clamping the material spoil it. It is unlikely that it will be possible to pull it back. Therefore, it is necessary to assess the situation in advance and decide whether there really is no other option for correcting it. Otherwise, it may be necessary to install a new tensioning material.

Features of removing the fabric

It was noted that in most cases, glazing beads or clips are used to attach this type of material. When dismantling them, it is not required to warm up the surface much. The product is fixed with self-clamping. Therefore, it is necessary to remove the cover completely. Or fastening systems or a baguette are deformed.

With the glazing option, start with removing the plinth. Then the profile is folded back, the fasteners are taken out. The blade is ready to be removed. When performing all the actions described, it is necessary to constantly warm up the working area with a gun or hair dryer. The coating should not cool down. Otherwise, sagging or small crackles cannot be avoided.

It is necessary to shoot the baguette as carefully as possible. This will keep it intact, without damage.

In most cases, skirting boards are glued to the wall. This allows you not to stain the material with glue and not to change it if you need to repair the ceiling covering. But if it is glued to the ceiling, then additional difficulties arise, because it must be disconnected from the material, and not from the wall.

When fastened with clips, the fabric trim is removed completely. Only part of it cannot be dismantled. This can lead to the blade falling out of the remaining clamps, which will damage the product.

Fabric types have no seams. Therefore, removing them is easier. No additional tools or unnecessary manipulations are required. With any fastening system, dismantling should start from the middle.

Is it possible to remove the stretch ceiling and tighten it again

Any canvas is suitable for removal. However, not all will work for reinstallation. Reuse is influenced by the type of fastening. Also, if the dismantling was carried out roughly or with errors, the material is deformed and its further use is impossible. This also applies to situations when it is planned to move material from one room to another. In this case, it is required to take into account many nuances, including the coincidence of both rooms in area. The second room may be smaller, but not larger.

Re-tensioning is possible only if the removal was carried out carefully, correctly, and the fastening system assumes the subsequent use of the blade.

Despite the durability of the tensioning structure, sometimes it becomes necessary to remove it. To do this, you need to take into account the type of fastening and whether the canvas will be reused. But first, the need for dismantling should be assessed. Perhaps the problem can be fixed without resorting to such a radical method.