Malfunctions of Darin's gas stove: an overview of typical breakdowns and how to fix them

Over time, all gas stoves tend to break, regardless of the brand of technology. The gas stove of the domestic manufacturer Darin was no exception, which after several years of operation may fail. Depending on the type of malfunction of Darin's gas stove, you can make repairs yourself, having previously studied the features of the device of this brand's equipment.

After all, you must admit that it is much more profitable to repair the equipment with your own hands than to spend time and money on calling the master.

Among the most common malfunctions of Darin's equipment are the termination of the gas control system, the formation of a crack on the electric ignition plug and the breakdown of the oven door. Repairing Darin's gas stove does not require special knowledge and skills from you, which means that you can find all the necessary information regarding methods for eliminating breakdowns of such equipment in our article.

Typical breakdowns of Darina's gas stove

As practice shows, in connection with the daily use of a gas stove, the auto-ignition system is the first to fail. A rather fragile device can break down due to the accidental ingress of water or food into the spark generation unit, due to which the function simply stops working.

To eliminate such a problem, it is enough to determine which part has failed and replace it with a new element.

To maintain the proper operation of the gas stove, it is important to timely clean not only the hob, but the control panel, including the internal parts of the body.

But it is far from always that equipment breaks down only because of pollution, which means that it is worth considering in more detail the most frequent breakdowns of Darin's gas stove.

Malfunction of electric ignition of the stove

When trying to ignite a hotplate, there may be a noticeable click, after which a spark usually appears, but not in this case. If only one burner does not turn on, then the problem most likely lies in the termination of the operation of the piezo ignition electrode (candle). Due to the long-term operation of the gas stove, a crack may appear on the ceramic surface of the candle, due to which electric ignition stops working.

Often, the auto-ignition function fails due to damage to the wire connecting the electrode and the spark generation unit. There is only one way to confirm the breakdown - remove the stove cover and press the ignition button. If the wire is damaged, then in the area of ​​the broken section you will see a spark jumping onto the plate body.

In both cases, the replacement of the broken part will be required in order to restore the operation of the piezo ignition system. The first thing that needs to be done is to disconnect the device from the power supply, however, before opening the top cover of Darin's gas stove, it is necessary to remove all the burners.

If two or all four burners do not work, then you will have to purchase a new ignition unit and replace it yourself.

Failure of the gas control system

All modern models of Darin gas stoves are equipped with a gas control system, which ensures the safe operation of equipment. Parallel to the electric ignition candle, a flame sensor is located on the burner - a thermocouple, which, when heated, generates an electric current. If the thermocouple is working properly, the valve opens to supply gas to the burner.

Otherwise, immediately after releasing the handle, the combustion will stop, which means only one thing - the solenoid valve did not work, and the supply of the combustible mixture to the burner is completely shut off.

The thermocouple can stop working due to elementary damage to the part itself, which is the wire connecting the flame sensor to the solenoid valve.

If, even after cleaning, the burner flame continues to go out, you will have to purchase a new one. thermocouple, and replace it on one's own. Since Darin's gas stove has its own structural features, the part should be selected in accordance with its model.

If possible, it is better to buy an original thermocouple - this will guarantee a long service life of the gas stove.

Burner jet clogged

The problem of contamination of the nozzle (jet) of the gas stove can arise due to the ingress of grease, detergents and gas combustion products. In this case, the repair will consist in cleaning the nozzle nozzle, while it is best to use a wooden toothpick.

Since it is far from always possible to effectively clean the orifice of the nozzle, it is recommended to disassemble the plate for better access to the part.

To do this, you need to remove the top panel, having previously unscrewed a few bolts, remove the jet, and clean it from the blockage. If necessary, the toothpick can be made a little thinner so that it can fit into the hole of the nozzle.

The most frequent breakdowns of jets relate only to their contamination, so it is extremely rare to change a part.

Need replacement of jets in a gas stove, Darina can occur only if you decide to switch from stationary blue fuel to liquefied gas from cylinders, and / or vice versa.

How to disassemble a gas stove?

Repairing Darin's equipment may require certain knowledge and skills, which is why it is so important to know how to properly disassemble a gas stove with your own hands. The first thing to do is to unplug the appliance and close the gas shut-off valve.

After ensuring your own safety, you can proceed to the next steps, sequentially disassembling each part of the technique.

Below we will show you how to remove the most important parts of the case to provide access to the necessary parts of the device. Since the internal structure of all gas stoves is almost the same, the following steps are suitable for disassembling equipment of any model.

Removing the handle of the gas stove

During use, the handles located on the control panel gradually become dirty, while grease can fall not only on the surface of the switches, but also inside their case, because of which they can be difficult turn around.

The only sure way is to remove the handles, clean them from accumulated grease and food debris using a soap or ammonia solution.

If the regulators are removed, it does not hurt to lower them in the solution for at least 5 minutes, and then clean off the remaining dirt using the hard side of a sponge or an old toothbrush. In this case, you should figure out how to properly remove the handles from Darin's gas stove without damaging the body of the equipment.

The handles on Darin's gas stove can be removed quite easily, and you do not have to pry them with a knife or screwdriver. First of all, we turn off the gas supply valve and check that all the handles are turned all the way. Next, with your fingertips, grasp the ring covering the holes behind the handle, rest your phalanges against the surface of the plate, and pull towards yourself until the handle comes off completely.

If the contamination is so strong that you cannot remove the handles yourself, you can try to gently pry them off with a chisel or knife. However, be careful not to scratch the hob body. Since the switches are plastic, you shouldn't pull on them with all your strength, otherwise you might just break them.

For more information on how to remove the handles from the gas stove and what to do if they cannot be removed - read Further.

Removing the oven door

Often, the need to remove the oven door arises due to the bending of the brackets, which makes it poorly covered.

This situation can occur due to congestion of the structure, for example, if a heavy object is placed on an open door. So, the brackets no longer perform their function of pressing the sash, and as a result, a gap appears between the door and the plate body.

Since the principle of fastening the oven door is the same for all stoves, it is worth familiarizing yourself with the uniform instructions for self-removing the door. First of all, you need to fully open the oven door, and find the door hinge latches that just hold it.

Next, it is important to follow the instructions presented, while maintaining the sequence of actions:

• we fold the door hinge latches back, and slowly close the door until they rest against the slots on the door;
• we pull the half-closed door towards ourselves, while the distance between the inner wall of the door and the oven should be equal to 10-15 cm, and slowly raise it;
• we remove the hinges from the slots on the body and remove the door without much effort.

In this case, it is important to take into account the severity of the door, so as not to accidentally drop it after removing it.

If the door has been successfully removed, the first thing you will need to do is assess the damage to the brackets and purchase new parts if necessary.

Conclusions and useful video on the topic

You can learn how to quickly remove the top panel of Darin's gas stove from this video:

Instructions for restoring the thermocouple of a gas oven are presented in the following video:

Despite the high build quality, Darin's gas stoves have their weak points, which just leads to premature breakdown of equipment, long before the end of their service life. To avoid large cash costs for calling the master, you need to understand the features of the device of Darin's gas stove, and independently eliminate the breakdown.

The article lists the most common equipment malfunctions, as well as discloses ways to eliminate them. Based on the instructions presented, you can personally disassemble Darin's gas stove and clean the contaminated parts or, in case of breakdown, replace them.

If you have already had to repair Darin's gas stove, having previously disassembled the necessary part of the case, please share your experience with our readers. In the comments under the article, you can tell the story of the breakdown of your gas stove, as well as talk about the difficulties that you had to face during the repair process.