Frequent errors when insulating the front door

In order to reduce the level of heat loss, homeowners often resort to such methods as warming the design of entrance doors. A wide range of materials offered for this purpose requires a thorough study of each.

/

As a heater for the door are most often used

Mineral wool - the material has a good property of heat and sound insulation, tolerates temperature changes with confidence. Environmental friendliness excludes the possibility of a negative impact on the health of people living in the house. A common mistake is the use of this material in doors that do not have stiffeners. The tendency of mineral wool to shrink often leads to a decrease in the level of heat protection.

/

Cellular filler - this material is presented in the form of a cardboard construction with honeycomb-type cells. It is not uncommon for owners to use this type of insulation, not paying attention to the fact that it has a weaker degree of noise and thermal insulation, even compared to mineral wool. Corrugated cardboard perfectly tolerates the effects of moisture and temperature changes, in addition, provides the fabric with additional rigidity.

instagram viewer

/

To the best of low cost, polystyrene is often used to insulate the door. It is characterized as a durable, moisture resistant material with a low level of thermal conductivity. In addition, the foam is inexpensive, safe for health and lightweight. When insulating doors with polystyrene foam, it is considered a mistake that not everyone takes into account its easy flammability and the release of toxic fumes during thermal exposure. This makes the material unsuitable for insulating the doors of the bathhouse and other rooms, the temperature of which reaches high levels.

/

Polyurethane foam has a high level of isolation. The peculiarity of the material allows you to completely eliminate the presence of voids in the interior of the door. In order to get the maximum effect from this insulation, you will need to use a specialized sprayer.

/

Speaking about the most common mistakes in the process of insulation of the door, it should be noted that many people do not take into account the increase in the total mass and size of the door, equipped with additional material. This feature requires the installation of stronger hardware and handles.

To the process of equipping the door leaf more easily, do not disassemble it in an upright position. It is best to partially dismantle the door and insulate it on a horizontal plane. This will allow you to more evenly and densely place the insulation.

Do not abuse the mounting foam. Its expansion property often causes problems with structural integrity.

/

When installing a new metal door, it is not necessary to dismantle the old one. An additional door will help create an air curtain that enhances the thermal insulation property.

Door insulation is often a necessary measure for reasons of imperfection of the factory design. In order to eliminate some errors during the insulation process, we recommend that you take into account the recommendations described, as well as analyze the qualitative properties of a particular insulation.

  • When an adjustable floor is more profitable than a capital screedWhen an adjustable floor is more profitable than a capital screed
  • What mistakes are made when the radiator is connected diagonally?What mistakes are made when the radiator is connected diagonally?
  • What are the consequences of building a site without permission?What are the consequences of building a site without permission?
  • What errors lead to water hammer in the heating system and how to avoid themWhat errors lead to water hammer in the heating system and how to avoid them
  • Why does the grinder work, but the disk does not spinWhy does the grinder work, but the disk does not spin
  • What could cause the cabinet door to bendWhat could cause the cabinet door to bend
  • 5 reasons to change the wizard without waiting for the repair to finish5 reasons to change the wizard without waiting for the repair to finish
  • How to cut tiles without dustHow to cut tiles without dust
  • How to cut a fiberboard with a flat edge with a regular grinderHow to cut a fiberboard with a flat edge with a regular grinder
  • Why you should not put aluminum radiators on central heatingWhy you should not put aluminum radiators on central heating
  • Why you can not allow for flaws in the installation of roof nodes from corrugated boardWhy you can not allow for flaws in the installation of roof nodes from corrugated board
  • What boards can not be used for half-timberedWhat boards can not be used for half-timbered

New publications are published daily on our channel in Yandex. Zen

Go to Yandex. Zen/
What kind of lighting impairs vision

What kind of lighting impairs visionHelpful Hints

Content 1 The benefits of reading in the dark 2 Computer monitor 3 Tip Many people remember from childhood the words of our mothers and grandmothers who insisted that you should not read in th...

Read More
What dishes are dangerous to health

What dishes are dangerous to healthHelpful Hints

During cooking, most often we pay attention only to the quality of the products used, while completely forgetting about the dishes. The fact is that some materials, during heating and interaction ...

Read More
What is the best paint for PVC panels?

What is the best paint for PVC panels?Helpful Hints

Sometimes it happens that you need to paint white PVC parts. For example, plastic windows and doors I want to make one tone with the interior or to strengthen the protection of panels from the dam...

Read More