Connecting a gas stove is a rather responsible action. But if you arm yourself with useful knowledge, watch a video, complete all the steps, then you can install this device competently, free of charge and no worse than professionals do.
Then you do not have to spend the whole day waiting for the foreman from the gas service, making an appointment a week or more in advance. And the cost of services (in Moscow, several thousand rubles) of a service center representative can be saved. And further the question: "How to connect a gas stove in an apartment on your own?" for you will be transferred to the category of completed.
Attention! Earned on our website kitchen designer. You can familiarize yourself with it and design your dream kitchen for free! May also come in handy wardrobes designer.
What documents are needed to install gas equipment?
- A document on the right to own housing and a certificate of state registration.
- Gas meter passport.
- Registration certificate for housing.
- Maintenance contract and previous gas subscriber book - if any. In the absence, it is concluded later.
You should listen to the instructions on the rules for using the device, sign an agreement and only then replace the equipment.
We remove the old slab and prepare for the installation of a new one
You can connect a gas stove within a few hours. Pay attention to the level of the floor - even and solid, without punching, will ensure flawless operation of the stove. A model with an electric oven, piezo igniter or backlight must have a freely accessible outlet.
When installing old equipment, the main problems can be sour threads on metal pipes or a shut-off valve. At this moment, there is a great danger of gas leakage. Therefore, you should close the doors to the remaining rooms and ventilate the kitchen well. After dismantling the old appliance, they usually install a socket, level the floor and carry out other necessary work.
Priority of actions:
- Free the plate from the packaging, remove the clips and the film. Take out the racks with baking sheets and remove their side.
- Observe the operating instructions and installation drawings. If all dimensions and settings are respected, the equipment will operate safely and without interruption.
- You can install the stove strictly horizontally using the twisting legs or a level. If there are no adjusting elements, measure the height with a tape measure and level it under it.
We connect the equipment - select the hose and connect the lowering
How to properly connect a gas stove with a flexible hose? The rubber sleeve is good for the lack of rigid attachment. You can move the device and choose the distance you need (up to 4 meters). In addition, the hose is also a kind of shock absorber. Even if you move the stove, there will be no gas leakage.
The hose serves for at least 10 years. Reinforced metal braid with yellow markings is suitable for gas lines, but blue and red ones are used only in water supply. Another option is a dielectric braided bellows sleeve. When buying a hose from a seller, be sure to take a certificate for the product. This document will then need to be presented to the Gorgaz employee who will check your equipment.
Pay attention to the end of the hose. If the stove has a downward-bent outlet (the so-called corner), then the hose should be bought the same. There are also different thread sizes. Most stoves use 1/2, but there are also 3/8. Then you cannot do without an additional adapter.
It is important to know the diameter inside the hose. If it is less than 1 centimeter, then at low pressure, or with all the burners turned on, the device will operate with an insufficient heat transfer coefficient and generate volatile harmful substances.
Priority of actions:
- Attach a new ball valve to the lowering. Petal have not been used for a long time, so it should be replaced.
- The plate is connected to the lowering (pipe with a closing valve) as follows: the hose connection is wrapped with fum tape or sealant. Then it is screwed into the ball valve, and the other end is connected to the outlet of the stove. It is also necessary to place a gasket with a metal mesh there, which will extend the life of the product and protect it from contamination.
- When using balloon gas (propane-butane), you cannot do without a reducer, a fitting and a special spout. The fitting is screwed onto the plate branch pipe through the gasket, the reducer is connected to the cylinder through the gasket.
- The last stage is tightening with open-end wrenches. Seal the hole in the drop with fum tape or other anaerobic sealant. If the stove is not connected in the next couple of days, a plastic plug should be installed on the new tap to prevent leakage.
- Open the valve, turn on the gas. Using soap suds, check all threaded points for leaks several times.
- Check the cooking zones and oven one at a time. Close all windows, and for half an hour, watch for a smell of gas in the room. Check the health of all electrical systems separately.
Work rules - take care of your safety!
The rules for connecting a gas stove in an apartment should be observed very precisely, since the device is a source of potential threat and the responsibility is very great. And only if all the rules are observed, the installation of a gas stove with your own hands will be the best way.
It is prohibited to seal the joints of the gas pipeline with gaskets made of plastic or rubber. This can only be done from fluoroplastic or paronite, fum tape or tow, additionally impregnated with a sealant.
When connecting, you should at the same time change the overhead shut-off valves to ball valves. These are more reliable and modern valves. Today, the whole world is installing a gas alarm next to the stove, which saves many lives.
If you cannot completely shut off the gas supply, it is forbidden to weld in the room, use a soldering iron or grinder.
Gas equipment should be periodically inspected and any problems that arise should be eliminated. To do this, you must have access to inspect the sleeve and all connection points. Under no circumstances should the hose be hidden in closed boxes or sewn up with drywall. Gas, accumulating in a confined space, explodes.
Never install the hob close to a wall. There should always be a gap. This is indicated in the instructions, and the distance depends on the type of product and its design features.
It is forbidden to paint the hose with any paint. There should be only two official connections in it (with a tap and a gas stove). All others are fined by Gorgaz.
Video: connecting a gas stove
average rating 0 / 5. Number of ratings: 0
No ratings yet. Be the first to rate.
