Washing machine Electrolux malfunction DIY repair - Setafi

Do-it-yourself repair of malfunctions of the Electrolux washing machine is possible if the breakdown is not too serious, and also with the appropriate experience. As a rule, the drain system becomes clogged, the drum fails, or the unit does not turn on at all. Repair instructions for common situations can be found in this resource.

If the machine does not start

It happens that the unit does not turn on or freezes and does not respond to commands. In this case, do-it-yourself repair of the Electrolux washing machine is carried out as follows:

1. First you need to check the plug - how tightly it fits to the outlet, whether the contacts are burned.
2. Next, check if the outlet is working.
3. If there has recently been a failure (voltage drop in the network), you need to turn off the device and wait a few minutes, and then plug it back in and start the program. Often this helps if no such incidents have been observed before.
instagram viewer
4. Perhaps the reason is related to the ingress of water or detergent on the control panel. Because of this, the keys stick, contacts deteriorate. Repair of a top-loading Electrolux washing machine in this case comes down to a thorough removal of moisture. If necessary, the panel will have to be disassembled and the oxidized contacts replaced.

If this does not help, the reason should be looked for in the network filter. Here the question arises of how to disassemble the Electrolux washing machine. The sequence of actions is as follows:

1. Remove the cover from above - for this, the bolts shown in the photo are unscrewed.
2. Find a filter located near the wall. It is he who can cause the Electrolux washing machine not to turn on.
3. If there are defects in the form of scorched, burnt parts and blisters, the part definitely needs to be changed. To do this, disconnect the wiring, remove the mounts and the tray to gain access to the keys.
4. Buttons can be found behind the control panel. They are pressed from the outside and pulled out from the inside, then a new part is put in.

Jammed door

Repair of a malfunction of the Electrolux washing machine is also carried out in the case when the door cannot close tightly. Because of this, the wash does not start, so the device does not actually work. It should be understood that the door is equipped with a mechanical lock and an electronic one. The breakdown can be related to either one or the other.

If the Electrolux washing machine does not start, proceed as follows:

1. Bend the rubber cuff.
2. Remove the clamp by prying it with a screwdriver.
3. Remove both screws.
4. Put your hand inside and get the blocking device.
5. If the Electrolux washing machine does not turn on, disconnect the contacts.
6. Install a new surge protector and then assemble all the parts in the opposite order.

Water does not enter or drain

Quite often, there are malfunctions of the Electrolux washing machine associated with improper supply and discharge of water. For example, liquid may not flow at all, or in one wash, the unit collects and drains it several times. Then the corresponding error code will light up on the display, depending on the specific model.

To find out the reason why the Electrolux washing machine does not work, as well as eliminate it, proceed as follows:

1. Close the tap, de-energize the device and disconnect the hose.
2. Behind it you can find a mesh filter, which is taken out with the help of pliers.
3. Then it must be washed under a powerful pressure of water to remove all contaminants. If necessary, manually remove large blockages and foreign objects. It will not be superfluous to disinfect the mesh with Domestos or another means.
4. Also clean the hose that supplies water. It can also become very clogged and cause the Electrolux washing machine not to turn on.
5. Remove the top cover, find the inlet valve at the back wall.
6. Take a multimeter and check the contacts in resistance measurement mode. It should be from 2 to 4 ohms, otherwise the part will definitely not work.
7. Next, the fasteners and wiring are removed, after which a new valve is installed.

There are also cases of a malfunction of the Electrolux top-loading washer, due to which it stopped, and the water remained in the tank. Then you need to do and clean the drain, acting like this:

1. Find a door under the loading hatch.
2. Open it, substitute a basin.
3. Unscrew the plastic outer part of the filter, moving counterclockwise.
4. Pull out the filter, remove debris and rinse under a powerful pressure of water.
5. Expand the unit, remove the cover at the back and find the pump.
6. To troubleshoot the Electrolux washing machine, you will need to remove the screws located around the perimeter.
7. Next, loosen the clamps that secure the hose and pipe. All details are cleaned.
8. The second end of the hose is also dismantled and washed under the pressure of water.
9. Especially carefully inspect the pump and impeller. It is cleaned from debris, foreign objects. If the engine burned out, which will be noticeable by the smell of burning, characteristic traces, the part must be replaced.

The drum is not spinning

When the Electrolux machine does not turn on, this may also be due to the fact that the drum does not rotate. The reasons are both simpler and quite serious:

1. You need to remove the back panel and inspect the drum. Perhaps the belt has come off the pulley - it is installed back so that the tension is maximum (like a string).
2. Next, inspect the engine. Perhaps the brushes are worn out - they are dismantled, the contacts are removed. If at least one is worn out by more than half, both should be replaced. In this case, you will need to disassemble the Electrolux washing machine.
3. It is also recommended to make sure that there is no foreign object. To do this, remove the heating element by removing the nut and gently loosening it from side to side. Then they take a flashlight and shine it into the hole left after the heating element. It is there that a foreign thing can be found, which is removed with tweezers.
4. The reason why the Electrolux washing machine does not turn on, and the drum does not spin, may be a breakdown of the tacho sensor. On the one hand, you need to make sure that it is properly fixed, and the contacts are intact. Next, the device is tested with a multimeter. If the resistance is not in the 60-70 ohm range, the part must be replaced.

Thus, in order to properly carry out repairs, it is important to know the design of the Electrolux washing machine with a top-loading or conventional front-loading. To do this, you can use the presented scheme. Then you need to accurately determine the cause, and then carry out repairs. If this is not possible, contact the master.