How is the bearing replaced in the Ariston washing machine? Do-it-yourself washing machine repair - Setafi

Replacing the bearing in the Ariston washing machine is necessary for each device after long-term operation. If the drum began to rotate with a clang, it does not wring out things well, this indicates the need for urgent repairs. You can conduct it yourself - how to do this is described in detail in the article.

Causes and signs of failure

Before you figure out how to change the bearing on the Ariston washing machine, you need to make sure that it is he who is faulty. Bearings break due to natural wear and tear, which occurs after several years of relatively intensive washing.

Instructions on how to change the bearing on the Ariston washing machine will have to be used when the following signs are noticeable:

1. Extraneous sounds appear during washing or rinsing, for example, grinding of metal surfaces or knocking. They also appear during the spin cycle, but are hardly noticeable due to the general noise.
instagram viewer
2. The spin quality has noticeably deteriorated, the laundry remains wet, even if there is not so much of it in the machine.
3. Replacing the Hotpoint Ariston bearing is also required in cases where the unit has clearly begun to swing strongly. Tracking this is not so easy, but in advanced cases it is more noticeable.
4. Sometimes the edges of the cuff can be damaged. While this does not necessarily indicate that the Hotpoint Ariston bearing needs to be replaced, it may be considered an additional indication.
5. Finally, after the end of the wash cycle, you can simply rotate the drum by hand. If it gives extraneous sounds, for example, a clang or, all the more, sways, an urgent replacement of the bearing in the Hotpoint Ariston washing machine is required.

Step-by-step instruction

By itself, bearing repair is impractical - it is simply replaced with a new one. This is easy enough to do, but to get to the part, you need to remove all the panels and even remove the tank. This is the main difficulty.

Moreover, this has to be done infrequently, since the elements rarely fail. But if repair is required, it is necessary to replace both bearings at once, and at the same time the oil seal, even if the spare parts are in relatively good condition.

To figure out how to replace the bearing in the Ariston washing machine, you need to prepare the tools at hand:

• pliers;
• a set of different screwdrivers, including curly ones;
• hammer;
• a set of keys - cap and open-end;
• a chisel may also be needed.

Since parsing is quite complex, and some parts are very heavy, it is better to work with two people. Replacing the drum bearing of the Ariston washing machine is carried out as follows:

1. Turn off the power to the unit, close the tap, dismantle the hose, drain the remaining liquid into a previously prepared container. Turn the back and unscrew each bolt on the rear panel.
2. Next, you need to remove the belt. It is very tight on the pulley, so it will take a lot of effort to dismantle it. It is recommended to inspect the belt, and if it is badly worn, purchase a new one and pull it over the pulley.
3. In order to replace the Ariston ARSL 85 bearing or another model correctly, you need to take some high-quality photos. This will help when installing the parts in reverse order to assemble them correctly.
4. Then you need to disconnect each element, including wiring. Take away the sensor that controls the temperature level. They work with it quite carefully, because the part is easily damaged. In order to properly replace the drum bearing of the Ariston washing machine, they also remove the heating element, if necessary, descale it.
5. Now remove each tie bolt that holds the rim of the drum, as shown in the photo. Remove gasket and cover.
6. Remove the drum and place it on a flat surface.
7. Remove the fastening nut, which is located in the center of the shaft.
8. Remove the drum cover and carefully place it on the stand. It is better to put a rubber or wooden board, and then start hitting with a hammer to knock the axle out of the bearing.
9. Next, the actual replacement of the bearing Ariston AVSL 109 or another model begins. They take an ordinary straight screwdriver and pry the oil seal with it, after which - the bearing. Similarly, you need to extract the second one. Handle them carefully to prevent deformation.
10.  Finally, the Hotpoint Ariston drum bearing is now being replaced. They put a new part and collect all the elements, moving in the reverse order.

Do bearings need to be lubricated?

When repairing, it is worth considering that even if new parts are installed, they must be lubricated immediately. Moreover, old bearings need lubrication. Since dismantling the drum is a time-consuming process, it is better to immediately carry out all the work overhaul and thereby increase the service life of newly delivered spare parts.

For lubrication, heat-resistant and moisture-resistant compounds must be used. However, they must not lead to hardening of the rubber, because otherwise the oil seal will suffer. The system will lose its tightness, which will cause leaks.

Experienced craftsmen recommend using such lubricants:

• AMPLIFON - high quality Italian product;
• Anderoll - a special composition for Indesit washing machines, although it is quite suitable for other brands, including Ariston;
• STABURAGS NBU 12 is a water and heat resistant composition that effectively protects bearings from wear;
• LIQUI MOLY is a thick lubricant that can withstand even very high temperatures up to +200 ०С (it is impossible to achieve them at home).

Now it’s clear how to change the bearing on the Ariston washing machine. This is a rather time-consuming process that requires certain skills. If there are any difficulties, it is better to seek the help of a master, because in the absence of experience, self-repair can lead to even more problems.