Zanussi washing machine: malfunctions and their elimination. Why won't the washer turn on and spin? – Setafi

Individual malfunctions of the Zanussi washing machine and their elimination are possible at home. For example, even at home, you can replace the heating element, clean the filter or install a new blocker. How to establish the cause and carry out repairs is described step by step in this article.

What parts break most often

In general, the Zanussi brand has established itself as a manufacturer of reliable household appliances. But the washing machines of this company have their weak points. Most often, the following elements fail:

1. The collection and drain system - especially in cases where the water is too hard, that is, it contains a lot of salts. Because of this, malfunctions of the Zanussi washing machine with vertical loading and horizontal loading occur. For prevention, cleaning should be carried out quite often, as it becomes clogged.
instagram viewer
2. Sunroof blocking device - it breaks quite often along with the sensor. This indicates a defect on the part of the manufacturer.
3. The heating element may build up scale. This is also due to too hard water, as well as problems with the tubular part of the heating element. This may be the reason that the Zanussi washing machine does not turn on or the process takes too long.
4. Drive Belt - It often fails as it is a less reliable mechanism compared to direct drive (i.e. no belt). If the Zanussi washing machine does not turn on, you need to pay attention to the condition of the belt. It is recommended to inspect it every 3-4 months.

Diagnostics: basic error codes

Almost all modern models diagnose errors automatically by indicating the corresponding code on the display. In the case of Zanussi brand models, most often users encounter such malfunctions:

1. E11 - no water supply for washing. In this case, the Zanussi washing machine does not turn on. It is enough to open the tap or make sure that the pressure is normal. If this does not help, you need to inspect the filter mesh - it may be clogged. Also check if the hose is intact, clean the filter. If possible, you need to make sure that the resistance of the coil from the valve is normal - the ohmmeter should show 3.8 kOhm.
2. E12 - violations of the gulf of water during the drying process. Such a code may light up 10 minutes after the start of the washing process. Then the malfunction is related to the bay valve.
3. E21 - you need to clean the filter of the drain system, since water cannot drain. Also check the pipes, they may be clogged. Otherwise, the Zanussi washing machine does not wring out.
4. E22 - the probable cause is related to the capacitor.

How to renovate a house

If the Zanussi washing machine does not turn on, in some cases it is really possible to carry out repairs on your own. For example, you can clean the filter or pipes, check the integrity of the hose, adjust the blocker, or replace the heating element. Step by step instructions for each case are described below.

Filter cleaning

The filter must be cleaned periodically on all models. It is not very difficult - the sequence of actions is as follows:

1. Unscrew and clean the inlet filter on the water pipe.
2. If it is not there, remove and clean the filter mesh. To do this, move the washer away and find the place where the fluid intake hose and the unit body are connected.
3. Remove the cover from above, dismantle the valve with the filter.
4. Dismantle the filter and rinse under running water.
5. Put all the details in place, moving according to the reverse algorithm.

Blocker replacement

If the Zanussi washing machine does not start, the reason may also be related to the blocker. It can fail both due to a manufacturer's error, and due to wear and tear or inaccurate actions.

This part, as a rule, is not repaired, but simply installed a new one. The sequence of actions is as follows:

1. Open the door.
2. On the right side, there are holes for the hook and 2 screws. They need to be unscrewed, as shown in the photo.
3. Remove sealant. To do this, pry off the wire clamp with a flat screwdriver and manually remove the rubber band.
4. If "Zanussi" does not wring out, disconnect the wires and take out the blocker.
5. Inspect it and make sure that the plastic part is intact. If it is broken, it remains only to purchase a new spare part. And you need to go to the store with the old part to buy exactly the same.
6. Then it is put in the same place and then the remaining elements are collected, moving in the reverse order.

Heating element replacement

Often, when the Zanussi washing machine does not turn on, the repair comes down to replacing the heating element. This is also a weak point, and in almost all models of different brands. If the unit shows an error code E05, this clearly indicates a breakdown of the heater. As a result, the water does not warm up, washing takes longer, and its quality is reduced.

For replacement, proceed as follows:

1. Unfold the unit and fit from the back.
2. Remove the bolts from the rear panel and then find a shank with 2 contacts and power wires, as shown in the photo.
3. With the help of a multitester, the resistance indicator is measured. If it is practically equal to 0, the heating element definitely needs to be replaced with a new one. If the value is from 20 to 4 ohms, then the heating element is working normally.
4. To dismantle the heater, remove the nut and disconnect the wires that go to it. This will help troubleshoot the Zanussi washing machine.
5. Remove the heater from the groove. This will require effort, because over a long period of operation it sticks. The use of WD-40 lubricant is recommended.
6. Loosening movements remove the old part and clean the adjacent surfaces.
7. To eliminate the violation, due to which Zanussi does not wring out, they put in a new heating element, connect the wiring and install the panel in place.

If the Zanussi machine does not turn on or wring out poorly, does not heat the water, self-repair can be carried out only in some cases. But if it is not possible to diagnose the cause or there are no necessary skills, it is better not to take risks and invite the master.