How to insert staples into a furniture stapler? Refueling Instructions - Setafi

There are several options for inserting staples into a furniture stapler. In general, the algorithm is the same, but there are several differences depending on the specific type of model. Basic rules and step-by-step instructions, as well as safety precautions are described in this article.

Loading the mechanical stapler

Furniture staplers, depending on the design features and energy source, are divided into 3 types:

• mechanical (set in motion by hand force);
• electrical (battery powered);
• pneumatic (work due to compressed air).

Depending on the type of device, the instructions will be slightly different. For example, if we consider how to insert staples into a mechanical stapler, the instruction would be:

1. Open the plate with the thumb and forefinger, acting with them simultaneously.
2. Pull it towards you and down. This will move the metal tab, which is located at the back of the plate.
instagram viewer
3. If there are unused staples left, they will fall out. At the same time, you can understand how to fill the stapler, and whether it is worth doing it.
4. New brackets are inserted into the receiver and the spring is returned to its original place.
5. Install the metal foot back.

Before starting work, it is recommended to check how the device works. If the correct method is chosen, how to assemble the stapler, it will function normally.

Features of charging other types

As already mentioned, there are different types of devices, and it also depends on how to charge a construction stapler. For example, if you choose a model with an electric motor, you need to act like this:

1. Block the tool using a special button or lever.
2. Pull out the groove by applying force or pressing the button.
3. Remove the inner rod by displacing the metal spring.
4. Put the staples on this rod and insert it back.
5. The next step on how to fill the furniture stapler is to put the rod back.

Checking the operation of an electrical device is quite simple. You need to remove it from the fuse and test the impact. If necessary, pre-charge the battery.

The main way to fill a pneumatic type construction stapler is the same as the technology described above. It is necessary to block the tool with a small lever, then pull out the groove, remove the spring and put the paper clips. Then the same steps are repeated in reverse order and the operation of the device is checked.

Since pneumatic models are powered by compressed air, they are quite noisy. In addition, they differ in large dimensions. Therefore, it is inconvenient to move devices from place to place. Another disadvantage is that the staples constantly fly out of the magazine due to exposure to pressurized air. Therefore, you should learn how to charge a furniture stapler - you will have to perform this operation quite often.

Precautions during operation

Instructions on how to change staples in a furniture stapler also require safety precautions. The basic rules are as follows:

1. There are no particular problems with how to fill the construction stapler with staples in the case of mechanical models. But if the device is electric or pneumatic, it must initially be blocked with a lever, and then get to work.
2. Do not use the device in rooms with significantly damp air.
3. The device of the stapler is such that it squeezes the staples, which sequentially fly out and are literally pressed into the work surface. Therefore, never point the device at yourself or other people or animals.
4. If charging is happening for the first time, you need to make sure which brackets match. To understand how to fill the stapler, you need to understand the type of staples (pay attention to the depth and width parameters).
5. If during long-term use the paperclip breaks and gets stuck in the store, you do not need to figure out how to fill the stapler with furniture staples. First you need to completely remove the magazine and remove the jammed bracket (one or more). After that, put new staples according to the instructions described above.

In general, safety precautions are simple. You need to work carefully, in a well-lit area. If the device is electric, it is first de-energized and only then proceed to replace the staples.

How many staples fit in the receiver

The answer to this question depends on the size of the working clip, that is, the magazine. To do this, you need to understand how to open a construction stapler and visually estimate the length. As a rule, it is enough to place the staples in 1 or even 1.5 rows. Since each of them contains 20 elements, about 30 brackets are placed in the device at a time.

And so that they are optimally suited for a particular device, you need to clarify the dimensions in the description for it. Today, brackets are popular, the types of which are indicated by numbers, for example, 53, 140. They have a width of 11.4 mm, 10.6 mm, respectively. There are also semicircular fasteners - they are designated by the number 36.

Now it’s clear how to load a construction stapler with staples. There is nothing difficult in this work - just open the top and put the staples in the store. But at the same time, it is important to make sure that the device is directed in the opposite direction, and also to put the mechanism on the stop.