What are the problems with the Kandy washing machine? Do-it-yourself repair, a step-by-step algorithm with a photo - Setafi

Kandy washing machine malfunctions that require do-it-yourself repair are most often associated with a drain pump, a heating element and bearings. These parts have to be changed even during normal use, because after a few years they become inoperative, which is quite normal. Instructions for diagnosing breakdowns and replacing the main elements are presented in this article.

The content of the article

  • Drain pump
  • A heating element
  • Worn bearings

Drain pump

Most often, users are faced with a breakdown of the drain pump. Buttons, parts of locks and even coins and other foreign things can get into it. They get stuck in the impeller, so it breaks. The pump motor runs with more force and may even burn out.

In these situations, it is not necessary to learn how to disassemble a Kandy washing machine. In fact, getting to the drain pump is quite simple. First you need to make sure that the pump really broke, and not another element. This can be done in a number of ways:

  • the machine drains water slowly;
  • the water has completely stopped draining;
  • instagram viewer
  • codes E3, E03 appeared on the screen, some devices may have E20.

You can eliminate the cause of this malfunction of the Kandy washing machine yourself - for this you should proceed as follows:

  1. Turn the unit back towards you.
  2. Feel the drain pipe - you may be able to find a blockage accumulation, a foreign object that has fallen.
  3. Unscrew all the bolts, remove the wiring and pull out the drain pump itself.Kandy washing machine malfunctions
  4. Carefully inspect it and, if necessary, rinse under running water. As you can see, disassembly of the Candy washing machine is not necessary, but a new drain pump may be required.

A heating element

Do-it-yourself Candy washing machine repair may also be needed in situations where the heating element, that is, the heating element, has broken. Over time, it becomes covered with a layer of scale, villi and other blockages. As a result, the heating element ceases to heat the water normally and works literally “for wear and tear”.

The element can burn out and fail, which is determined by several signs:

  • the water stays cool;
  • things are poorly washed;
  • washing is interrupted, a specific error code appears on the screen (depending on the model, this can be E3, 5, 14 or 22).
  • noticeable smell of burning (neglected case).

To repair or replace the heating element, it is necessary to remove and inspect it. Step-by-step instructions on how to disassemble the Kandy washing machine, as well as install a new heating element, are as follows:

  1. Find the right place - the part is located below the tank. To get to it, unscrew all the bolts and remove the back panel.How to disassemble a Kandy washing machine
  2. The heating element itself is not visible, but it can be identified by the wires that go into the depths.Teng
  3. Remove all wires, having previously photographed them, so that they can then be correctly returned to their place.
  4. Measure the voltage with a multimeter. If it is within 20-30 ohms, the device is working normally, and the cause of the violation should be sought in another part. Although do not forget that the heating element could simply become clogged. Then it is washed with a solution of citric acid (add 2 tablespoons to the powder tray and start washing).Repair
  5. If there are doubts about the performance of the heating element, it is removed - this is exactly what the next stage of repairing the Kandy washing machine with your own hands is connected with. It is necessary to loosen the nut (1) and push the panel inward, then pry it off with a regular screwdriver and carefully remove the part.Washing machine repair
  6. Next, the heater is inspected and cleaned of scale. If it breaks (there is no resistance on the multimeter), you need to put a new element and do the same steps, but in reverse order.

Worn bearings

The question of how to disassemble the Candy washing machine also arises when the bearings wear out. Installing them is not so easy, and the breakdown is considered serious, because the drum may also suffer due to their wear. To diagnose this breakdown, it is recommended to pay attention to the following signs:

  • spin does not work;
  • during push-ups, extraneous sounds are heard (creak, rumble);
  • the drum does not rotate or falls below the normal position;
  • during the analysis, rusty smudges can be seen on the surface of the tank.

Due to worn bearings, the Kandy washing machine does not work, therefore, without eliminating this breakdown, it will not be possible to start the program. During the repair, they act like this:

  1. Remove the clips that hold the water intake hose, unscrew each bolt and remove the cover from behind.1
  2. If the machine is equipped with a belt, it must be removed from the pulley.2
  3. Then the temperature sensor is disconnected and bent away - it is quite fragile, so it is important to work carefully so as not to break it.3
  4. Remove the bolts that fix the rim of the drum, then the gasket is removed and the cover is removed.4
  5. Take out the drum and put it on the floor.5
  6. Unscrew the central nut from the shaft.6
  7. After the cover is removed, it must be laid on a wooden or rubber board, then start knocking the drum axle out of the bearing with a hammer.7
  8. Using a straight screwdriver, pull out the oil seal, then the bearing. Remove the other bearing in the same way.8
  9. In order to properly repair the Kandy washing machine on your own, you need to thoroughly lubricate the surfaces with Litol. Then install new bearings and an oil seal. Even if only one part is worn out, it is better to replace everything at once.

Washing machine repairs can usually be done at home. This requires improvised tools and at least minimal skills. But if the breakdown is serious, for example, related to the control module, it is better to contact the master. Independent actions in such cases can lead to major damage.

Installing a valve on a heating battery: how to install ball valves - Setafi

Installing a valve on a heating battery: how to install ball valves - SetafiHomeUncategorized

It is not difficult to figure out how to put taps on radiators. In fact, you need a minimum of tools to work. First you need to unscrew and dismantle the radiator, as well as the old valve. How to ...

Read More
How to display an image from an iPhone to a TV: step by step instructions - Setafi

How to display an image from an iPhone to a TV: step by step instructions - SetafiHomeElectronics

You can figure out how to display an image from an iPhone to a TV in just a minute. To do this, follow a few simple steps, after connecting the devices to Wi-Fi. There are other ways - instructions...

Read More
How to clean a new refrigerator before first use: tips - Setafi

How to clean a new refrigerator before first use: tips - SetafiHomeAppliancesFridge

After the purchase, the question arises of how to wash the new refrigerator before the first use. On the one hand, you can use ready-made products in the form of a spray or liquid composition, whic...

Read More