What malfunctions does the Whirlpool top-loading washing machine have? Whirlpool Washing Machine Error Codes and Solutions - Setafi

Top-loading whirlpool washing machine failures are usually related to items that wear out quickly, such as bearings, a drive belt, or a drain pump. All modern devices carry out diagnostics automatically and show the corresponding codes on a small screen. A complete list of codes and their decoding can be found in the presented article.

Basic error codes

First of all, you need to figure out what the Whirlpool washing machine error codes are. If the model has a display, when a problem occurs, it conducts self-diagnosis and determines the cause, after which it issues a specific code:

1. F01 or F13 (also referred to FH) – the device does not draw water or does not draw enough water. It is necessary to check the pressure and, in principle, the presence of water, open the tap completely. The mesh filter may need to be cleaned.
2. F02 (another notation FA) - the machine may have leaked. If there are no signs of a leak, you can simply unplug the device and plug it back in to fix a one-time system failure.
instagram viewer
3. F03 (Also FP) - water drains very slowly or remains in the tank at all. In this case, the reason may be related to the choice of the mode without draining water or clogging of the hose or drain filter.
4. F04 - the water does not have time to warm up with a heating element, it remains noticeably cool. The reason is probably related to the heating device. Moreover, if the Whirlpool washing machine does not turn on or the liquid remains cold, the heating element needs to be changed.
5. F05 - Breakdowns are connected with the water heating system. You may need to change the temperature sensor or repair the wiring.
6. F06 or F15 - such Whirlpool error codes indicate that the sensor for measuring the number of drum revolutions is not in contact with the control module. It is recommended to try to remove the laundry from the tank and wash it 2 times.
7. F07 - such errors of the Whirlpool washing machine can indicate violations in the operation of the triac, that is radio element that transmits signals from the board to different sensors, for example, temperature. The solution is to replace the part.
8. F08 And F12 – in this case, washing is not possible because the water is not heated. Moreover, the heating process does not even begin. The reason is related to the breakdown of the pressure switch.
9. F09 - water constantly enters the unit, which is also the cause of a malfunction of the top-loading washing machine. It is recommended to check and, if necessary, clean the sensor that measures the water level. It may be necessary to install a new electric valve or controller.
10. F10 - these Whirlpool error codes indicate that the motor needs to be repaired or replaced.
11. F11 (indicated on some models) F19) - the power system has broken down, there is insufficient voltage in the network, so the washing process does not start.
12. F14 - problems in the operation of the microprocessor, you can try to turn off the unit and turn it back on in a few minutes.
13. F16 (Also F20 or F21) - these Whirlpool washing machine error codes indicate problems with the processor.
14. F18 – Foam during washing is formed in large quantities, so you should reduce the amount of detergent.
15. F22 - violations in the operation of the heating element or contamination of the dispenser.
16.  Whirlpool error F23 occurs very often, it indicates the need to clean the tubes of the sensor that determines the water level. Sometimes the problem can be related to the control module.
17. F24 - too much water in the tank, the pressure switch needs to be replaced.
18. F26 – problems with the engine, it does not function.
19.  F27 - the drum rotates only in one direction, problems with the reverse relay.
20. F28 - the drum rotates, but its speed has become noticeably slower. At the same time, it cannot be said that the Whirlpool washing machine does not turn on. It functions, but not in the usual way.
21. F31 – software failures, you need to contact Whirlpool technical support.
22. FDL – the lid does not block during washing, repair is necessary. There are such malfunctions with a front-loading Whirlpool washing machine.
23.  FDU – the lid does not close or does not open. You need to see if the lock works, if foreign things have got into it, and try to close the door with a little effort.
24. bdd – the drum doors remain open. It is necessary to press and hold the RESET button for 5 seconds, then open the door, and, on the contrary, close the shutters.

The most common faults

As you can see, Whirlpool washing machine errors can be associated with a variety of device elements. In this case, the drain pump, heating element and other components most often break down. The most common violations are:

1. A breakdown of the drain pump leads to the fact that the water will flow very slowly or the machine will completely stop draining it. The motor may burn out, and then the pump will stop making characteristic sounds. Part replacement required.
2. Problems on the part of the heating element - the water does not heat up well, there may be a smell of burning or even plugs in the meter can be knocked out. It will need cleaning or a complete replacement of the heating element.
3. Breakdown of the electronic control module - it is necessary to clean or re-solder the contacts, faulty tracks. Sometimes it may be necessary to completely replace the board.
4. The drive belt has broken, which is why the drum does not rotate. Error codes for the Whirlpool F28 washing machine or others may appear. It is necessary to inspect the belt and replace it or put it back on the pulley.
5. Bearings were worn out, because of which the drum began to “hang out” when touched and during operation. In this case, you will need to completely replace them.

It is worth noting that Whirlpool error codes can be determined without a display. They are used on models without a display and are a combination of several indicators. If you cannot determine the exact cause yourself, it is better to contact a specialist, since home repairs without the necessary knowledge can lead to even more damage.