Zanussi washing machine: malfunctions, do-it-yourself repairs at home - Setafi

In the event of malfunctions of the Zanussi washing machine, do-it-yourself repairs are possible. But first you need to accurately determine the cause, and then fix the problem. If there are doubts about the correctness of the diagnosis or a complex element (electronics) has broken down, it is recommended to call the wizard.

Spin and drain violations

Often the causes of a breakdown are due to the fact that the machine does not completely drain the residual water or does not wring clothes well. As a result, it comes out too wet, not dry enough. Before you start repairing a Zanussi washing machine with your own hands, you need to make sure that the diagnosis is correct.

The device itself will show 1 of 3 error codes on the display:

• E21;
• E23;
• E24.

You can fix the problem yourself. To do this, it is recommended to proceed as follows:

1. Turn off the supply tap and unplug the washing machine from the outlet.
2. Wait until it cools down (including the powder).
instagram viewer
3. Open panel.
4. Remove the drain hose and plug it.
5. Rotate the pump cap in a counterclockwise direction.
6. Remove excess items from the hose (if any).

If the pump blades turn freely, you can screw the cover back on and put the panel back in place. To make sure that the device is working properly, you just need to drain the water without clothes (idle).

If this does not help, do-it-yourself Zanussi washing machine repair should affect other elements:

• filter - to clear it of blockages, you need to remove the element and rinse well;
• pipe that connects the pump and tank;
• drain hose.

The cause of the violations may not be directly related to the machine. It is recommended to check the sink (namely the siphon) and the drain pipe (sewer). Often they are the cause of clogging, which is why the spin and drain do not work properly.

If this does not help, the reason may be related to the following elements:

1. The “No spin” option is enabled - then there is no malfunction, and there is no need to repair the Zanussi washing machine.
2. The regulator that turns off the spin does not work.
3. In rare cases, a malfunction may occur due to damage to the motor or the heating element. Then they should be replaced, but it is better to entrust such work to a professional.

extraneous sounds

Extra sounds manifest themselves in the noisy operation of the engine. It may hum, although it does not rotate the drum. Then you should turn off the machine and replace the bearings, which are already clearly worn out. They are closed with glands, and if water penetrates under the gland, the bearing itself quickly breaks.

Do-it-yourself Zanussi washing machine repair can be implemented according to the following algorithm:

1. Remove the plug from the socket.
2. Drain completely the liquid.
3. Remove all outer panels.
4. Disconnect the drive belt from the tank, also remove the remaining elements (spring, temperature sensor with pipes and counterweight).
5. Disconnect the pulley from the drum.
6. Take the bearings together with the drum axis and separate them from each other.
7. Mount new bearings and install the remaining elements.

In general, this is a sufficient measure, but noise can be associated with other factors. For example, an object gets stuck between the tank and the drum - then it must be removed. There may also be wear on the drive belt (it is replaced by another) or poor fixation of the pulley (the bolt is tightened by hand).

Electronics breakdowns

This is the most difficult case when do-it-yourself repair of a Zanussi car can only be done with the appropriate knowledge and at least minimal experience. For example, often a violation is associated with a burnt-out triac. It needs to be replaced, and the tracks must be soldered on the electronic system module.

It also happens that the module itself fails. It is unrealistic to repair it - you just have to replace the part. Usually an experienced craftsman is called for this. Independent actions can lead to even greater damage.

Thus, in many cases, do-it-yourself repair of the Zanussi washing machine can be done independently. In most cases, it is enough to inspect the tank, as well as the hose and other components. But if this does not help or the electronics are broken, it is better not to take risks and invite the master.