Replacing a bearing in an Ariston washing machine is a rather laborious operation that requires certain skills, improvised tools and space. The fact is that the bearings are located under the drum, and in order to get to them, you have to disassemble almost the entire unit. How to do this correctly is described in detail in the material presented.
The content of the article
- When replacement is required
- Preparing for a replacement
- Dismantling the machine
- Bearing replacement
When replacement is required
Before you understand how to change the bearing on the Ariston washing machine, you should understand the diagnostic rules. Normally, this part wears out earlier than after 5-6 years of continuous operation. Often the service life reaches even 10 years.
But if you constantly overload the drum, the stuffing box will lose its tightness, so water will get on the bearing, the grease will begin to wash out. All this leads to premature wear of the part, for example, after 3-4 years. Breakage can happen in the first year of use due to factory defects. But such cases are very rare.
Hotpoint Ariston bearing replacement is required when the following signs are observed:
- strong vibration, noise in the spin mode;
- rocking the drum (if you move it with your hand in a calm state);
- uneven rotation of the drum (you also need to move it with your hand);
- damage to the edges of the cuff;
- poor spinning of the laundry, even if the drum is not fully loaded, for example, half.
Hotpoint Ariston bearing replacement is best done as soon as possible. Otherwise, the drum itself may break, and such repairs are more time-consuming and more expensive. If in doubt, it is better to call an experienced craftsman for diagnostics and restoration work.
Preparing for a replacement
Replacing a bearing in a Hotpoint Ariston washing machine involves the prior purchase of an original part from a trusted store. Moreover, it is necessary to take not only the bearing itself, but also the oil seal. The replacement is carried out at the same time, because otherwise the old part will begin to wear out the new one, and in just a few months or a year another repair will be needed.
Before starting work, you need to study the instructions on how to replace the bearing in the Ariston washing machine, as well as prepare the tools and materials at hand:
- a set of screwdrivers of different types;
- in some cases, wire cutters are required;
- ordinary hammer;
- pliers are required;
- socket type wrenches (set);
- bit;
- glue;
- puller (optional);
- liquid WD-40;
- pelvis
It is also important to make sure that there is enough space for repairs, because the car will have to be almost completely disassembled, turned on different sides. It is better to remove all furniture and other items, in extreme cases - to perform work elsewhere, for example, in the garage.
Dismantling the machine
Replacing the drum bearing of the Ariston washing machine begins with the fact that the unit is turned off, the plug is removed from the network, and the cold water tap is turned off. The hose is also disconnected from the entrance to the housing and suspended. A basin is placed in advance and the water is completely drained.
Next, the replacement of the Ariston ARSL 85 bearing or another model begins, the main steps are as follows:
- At the bottom they find a hatch, open it by removing the latches. They dismantle the drain filter, again substitute a small container, put a rag on it to glass the water.
- Extend the unit so that you can access the panel from behind. Remove the 2 screws that secure the top panel. Move it forward and dismantle it.
- To put a new drum bearing on the Ariston washing machine, remove the panel from the back. And for this you need to unscrew each screw in sequence. You also need to remove the drive belt, if the unit is equipped with it. Manually scroll the pulley and pull the belt towards you.
- Again they approach the front side and remove the tray, where they pour the powder, pour in the conditioner. It is simply pulled towards itself and pressed on the latch, which is located in the middle. Remove the bolts behind the latch, disconnect the plastic latches. The panel will remain on the wires, as seen in the photo - they should not be removed, it is easier to leave them as they are.
- By itself, replacing an Ariston AVSL 109 bearing or another model is a simple operation. But its complexity is associated with preliminary preparation, namely, the dismantling of other parts that prevent getting to the main part. It will be necessary, for example, to remove the powder receiver by loosening the nozzle tension. It is also removed and the valve contacts are disconnected.
- Unscrew the screws that secure the lock that blocks the hatch.
- If there is a risk of damage to the glass of the hatch, it is also better to remove it along with the door by removing the corresponding mount.
- At the bottom of the tank, the wiring going to the electric motor is removed. This is one of the last steps before the Hotpoint Ariston drum bearing replacement begins. Clamps, if necessary, are cut with wire cutters, move the bundle of wires away so as not to interfere.
- Unscrew the screws that fix the shock absorbers and carefully remove the drum with a hook.
Bearing replacement
The disassembly stage is completed - it remains only to carry out the actual replacement of worn elements. You should act like this:
- Take off the pulley. It is stopped with a stick and then the central bolt is unscrewed. If it goes very tight, it is treated with WD-40.
- When the pulley is removed, you can disassemble the tank. To do this, unscrew each bolt, moving sequentially. Then the latches are removed and the upper half is disconnected.
- Gently hit the bushing with a hammer until the drum pops out.
- The tank is turned over, put the outer half towards you. A chisel is installed on the surface of the clip and hit with a hammer. Remove the inner bearing in the same way. If there is a special tool = puller - it will be easier to work.
- Install new bearings, pre-cleaning the place with WD-40 fluid and removing any remaining dirt. An oil seal is placed on top.
- They clean the sleeve from traces of rusty deposits and only after that put the drum in place.
Now it’s clear how to change the bearing on the Ariston washing machine. After installing new elements, connect all the parts, moving in reverse order. Then you can rotate the drum a little to check how evenly it moves.