Homemade hose holders: on a barrel, on a wall for storage

The operation and storage of a garden hose requires compliance with certain nuances. For convenient and correct use, various devices are invented. One of them is the holder. There are devices for mounting on a barrel or storage.

The first is necessary so that the hose does not “run away” from the container while collecting water. The holder can be purchased or made by yourself. Let's look at examples of such devices designed for mounting on a barrel, and also figure out how to make a wall bracket for storage hose so that it does not constantly dangle under your feet during the gardening season.

Barrel holders

You can use wire to create a cheap and simple holder. You will need a thick and durable variety - you need to insert it into the hose. Then fix the ends on the last one so that it cannot slip out. Next, the product is bent and placed in a barrel. Thanks to this type of clamp, the hose will keep its shape well and will definitely not “escape” from the container.

Another fastening option can be made from wire - make a loop out of it and pass the hose inside it. The ends of the loop are fixed to a container for collecting water. It is better if the fasteners rise about ten centimeters above the level of the barrel. This way you can control the filling process, even from a certain distance.

A large office clip can serve as a holder. The largest models that can be found in stores are 5 cm wide. The circumference of the rings in their upper part is approximately two cm. The clamp size should be selected based on the diameter of the hose. The stationery product just needs to be secured to the edge of the container, and the hose threaded into the ring. The clamp holds well and does not fall off. And due to the rim, which, as a rule, is located on top of the barrel, even greater reliability of fixation is ensured.

It is not at all difficult to secure any bracket inside the container for collecting water. It will hold and guide the hose. Suitable for these purposes:

• door knob;
• metal corner or ring;
• piece of tire.

The main thing is that the hose can pass through the hole.

There are specialized fasteners that can be purchased at building materials or garden supply stores. The cost of simple plastic models is from 300 rubles. Purchasing fixtures can be costly if there are several barrels on the property.

A simple holder can be made from a plastic bottle cork. It is necessary that its diameter is slightly larger than the circumference of the hose. Make a ring from the lid by cutting off its back part. The resulting clamp must be attached to the container and the hose inserted into it.

The holder can serve a device used to attach a washing machine hose. It can be purchased at hardware or household supply stores. The lock on the barrel will be reliable and convenient.

A handle from an old leaky bucket Can be used as a holder. The hook on one side needs to be bent, and left on the other. Then you should insert the part into hose straight end forward, fixing it on the edge of the rubber product with the remaining hook. This is necessary so that the handle does not fall out while filling the barrel with water. The hose should be placed in the shape of a month on the edge of the container - it will hold well and will not fall out.

Wall Mounted Hose Storage Holder

Such a device will help you carefully and conveniently place the watering product in a specially designated place.

Needed:

• sheet of metal - it should be about 1 mm thick;
• profile pipe;
• metal strip.

Step-by-step process for making homemade products

You need to start by cutting two semicircular blanks from a metal sheet. They must be identical to each other. In one of them, a semicircle is cut out in the lower part.

Then you need to:

• process them on a grinding machine - this procedure will help to trim the edges and remove sharp burrs;
  

  @sdelairukami.ru

• cut blanks from a strip of metal and weld two arcs of the same size from them;
• clean weld seams with a grinder;
  

  @sdelairukami.ru

• cut blanks of the same length from a square profile - they should be used to weld two arcs together to obtain a solid structure;
  

  @sdelairukami.ru

• weld the sheet blanks to the metal base.

The assembled structure must be painted.

You can decorate the front part. To do this, holes of the required diameter should be drilled in one semicircular element. Insert furniture bolts into them. Then scald from the inside. The part of the studs that protrudes needs to be cut off with a grinder.

Wall mount

Having decided on the location of the holder - it is better if it is near the water tap - you need to drill holes and hammer plastic dowels into them. Next, use self-tapping screws to attach the product to the wall. Now you can wind the watering hose.

You can see clearly how to make a simple wall-mounted hose holder with your own hands in the next video.