Repair faults dishwashers Electrolux

Dishwashers from Electrolux is a fairly common phenomenon in Russia. Despite the high quality of components and assembly of the Electrolux dishwasher, it, like other units and devices, can break down and requires the utmost attention and prevention. Before you begin to repair, you need to diagnose problems, identify typical and learn about existing methods of repair. In this article we will try to tell you about how to repair Electrolux dishwashers and other intricacies associated with this process.

Consider the basic failures of

machines. Most dishwashers supplied to the Russian market are manufactured in Poland and account for about 90%.The quality of their components and assemblies can be compared with similar units of German and Swedish companies, however, as they say, there is no choice. Most experts distinguish the following advantages of household appliances produced by Electrolux:

• ; all components are made exclusively from high-quality raw materials;
• really reasonably approached the development of circulating pumps, they had a high working life;
• manufacturer cares for small parts such as: wires, clamps, terminals, rubber bands and filters, which in turn has increased the period of trouble-free operation of the dishwasher.

There were no particularly critical drawbacks found during the operation of the dishwasher; one of them, like everyone else, has typical breakdowns, from which it is rather difficult to protect. Here is a list of them below:

• clogging of drain and filler pipes;
• crashes in the water program;
• quality problems with washing dishes;
• TEN( heating element) does not sufficiently heat the water.

Fill and drain connections

Drain and fill connections can clog not only at Electrolux dishwashers, this is a common problem for these units. The rate at which they will clog depends on the quality of the water, the content of minerals and metals in the water. This is due to the fact that they settle on the walls, after which they simply clog them.

In case of detection of this damage, repair will be quite a simple process. You will need to clean the clogged filter, after which we recommend performing this operation regularly, so as not to encounter a problem in the future. The use of chemicals, such as "Kalgon", in some way does not prevent the formation of plaque on the filter and pipes. It only protects internal components.

In case you have rather hard water, you need to monitor the dishwasher more carefully and clean the parts described above more often. How exactly to make it?

• turn off the water with a tee-valve;
• disconnect the filler hose with flow filter on both sides of the tee tap and dishwasher;
• dismantle a small flow filter from the dishwasher body( it is located at the beginning of the filler path, where the inlet hose is installed);Clean the
• and then rinse the hose together with the filters with running water;
• assemble the device.

It is worth noting that when installing a dishwasher, some do not install a flow filter directly between the tap-tee and the hose. In this situation, only one filter will be clogged, the one that is installed at the beginning of the filler pipe.

Much more often, the pipes and hoses of the drain truck, garbage filters are clogged. Experts recommend that users perform periodic inspections of spare parts data, at least once every two months. In the case when the dishwasher is used intensively, namely several times a day, it is necessary to check every 1-1.5 months. In order to protect the units from driving, you must adhere to the following simple rules:

1. Before placing the dishes inside the unit, with a paper napkin, remove large leftover food.
2. Use only high-quality detergents, or make them yourself.
3. Check the capacity in which the regenerating salts are located; it should never reach a critical level.
4. After each washing process, perform a visual inspection of the garbage filters, and if necessary, clean it.

Problems with the heating element

If you notice that the water in the dishwasher does not heat up enough, then most likely there is a problem with the heating element, or with a temperature sensor or other control modules. Electrolux dishwashers are quite sensitive to voltage fluctuations, as well as to its glut. What could this lead to?

In the best case, you will get rid of a blown fuse, at worst, several of the triacs of the control board may burn. After this, the control module simply will not be able to send signals to the heating element, or will do so with a delay or perform incorrectly. Repairing an malfunction is quite a laborious and expensive task; you need:

• to disassemble the dishwasher in half in order to get to the TEN;
• check the integrity of the wires going to the Teng and measure the resistance with a multimeter;
• check the details of the control module, in case of failure, replace it with a new one.

We want to note that in order to protect household appliances and other appliances from voltage surges, you can use a voltage stabilizer, which is purchased separately.

If you do not understand this topic, the best solution would be to call a specialist who accurately diagnoses the damage and fix it in the shortest possible time.

Failure of the dishwasher to perform the washing program of the

A rather frequent occurrence, during the execution of the washing program, it simply hangs. Most often, to solve the problem, it is necessary to reboot the dishwasher, saying it is easier, you need to turn off the device for just a couple of minutes, and then return the power supply to it again.

In case this problem recurs with all dishwashing programs, it is necessary to call a specialist who will check everything carefully and replace the damaged part in case of a defect or defect.

Pay attention! On some models of the dishwashers Electrolux replacement of the control module costs a lot of money. In this situation, it will be easier for you to buy a new dishwasher than to replace a faulty control module.

However, do not be upset, this problem is most often associated with an error in the operation of the following sensors, namely: pressure switch, aqua-sensor, and others. Sometimes to the fact that the whole group of sensors fails, the electrical network is involved.

In this article, we looked at how to repair your own Electrolux dishwashers. However, remember, if you do not understand anything in technology, the best solution will be to turn to specialists who will carry out all the repairs themselves, and you will not have to spend your nerves and money on unjustified actions.