The washing machine is constantly drawing water and immediately draining - what to do?

control unit in the laundry washing machine the washing process drains the water at least twice. The first time - at the very wash and again - when rinsing the washed laundry. There are modes in which the washing machine collects and drains water more than twice. If the washing machine is constantly pumping water and draining it, it means something happens and it must be immediately turned off and find out the cause of the fault.

This problem may occur if your washing machine is improperly connected or there is a breakdown. This article will help to find out the reason why the washing machine constantly collects water into the tank and immediately drains it.

Possible causes of malfunction

If your washing machine is continuously drawing water - this is a bad sign and this problem needs to be solved immediately if you plan to use your appliances in the future. There are many reasons why a machine stops working properly. It is necessary to understand all possible causes, and cutting out irrelevant, to identify the real reason that the washing machine does not stop pumping water.

Here are the main reasons for the inoperability of the machine:

• Errors were made when connecting the washing machine to the water supply and drainage system.
• During operation, the washing machine tank lost its tightness and began to pass water.
• The sensor, which is used to determine the level of water in the tank, has failed.
• The inlet valve, which regulates the water supply, has stopped working normally. The
• control unit has stopped functioning normally.

If you just bought a car, the presence of a problem may indicate a factory defect. Maybe in the new washing machine, there is a defective part, or problems with electronics.

Washer is incorrectly connected

If you have just bought a washing machine and are sure that it is absolutely intact, but for some reason it is constantly drawing water, it says that the drain hose is most likely connected incorrectly.

If the connection of the washing machine is carried out by a non-professional who is not familiar with the elementary laws of physics, a so-called “siphon effect” may appear. This leads to the fact that the used water from the sewage system begins to flow into the switched off washing machine. And when the washing machine works, it will always pump clean water, which will also constantly pour into the sewer.

You will immediately feel that your water consumption will increase dramatically, a washing machine will either be poorly washed or will not be washed at all.

To correct this problem, it is necessary to properly organize the drain system by raising the drain hose 50-60 cm from the floor level or installing an anti-siphon valve on the hose. It is preferable not to install a siphon valve, which requires periodic cleaning, but to properly organize the drain system.

The leaky tank of the washing machine

If the tank in your washing machine is leaky, it will immediately be noticeable through the puddles on the floor. The electronic unit will give a constant signal for injection, but not the tightness of the tank will not allow the machine to work normally and its pump will constantly supply new water to the leaky tank.

In modern machines there are special systems “aqua-stop”, which block the flow and discharge of water in case of a leak in the tank. Usually in this case, it is necessary to replace the tank. Welding or soldering modern tanks is often impossible because of the material from which they are made.

Tip:

Read also: The washing machine flows from the bottom during the washing

The

pressure switch is out of order

Another reason why a washing machine continuously fills water is the failure of the water level sensor. A water level sensor is a device by which an electronic unit measures how much water is in a tank. If the command from the sensor is incorrect, then the electronics considers that there is not enough water in the machine and gives the command to fill the tank. This problem is solved by replacing the pressure switch or its repair. This device can highlight the following problems:

1. The membrane rubber loses tightness. In the process of work, all rubber parts gradually lose their properties and require replacement.
2. Oxidized sensor contacts. They need to be cleaned. If the contacts are very rusty, they must be replaced.
3. Cracks in the sensor tube. In this case, you need to completely change the block. Qualitatively fix such a problem is very difficult.

It is worth considering that the pressure switch is not a very expensive device, even on new modern cars. Therefore, if there are problems with it, the easiest way is to purchase a new one and put it in a washing machine.

Failure of the inlet valve

If the inlet valve has ceased to function properly in the washer, this may also be the reason for the apparatus to continuously fill cold water. If the valve has lost its technical characteristics, water will continuously flow into the washing machine. At the same time, it does not even matter whether the machine is on or off. At the same time, the consumption of cold water will greatly increase. Repair input valve can not be. You must purchase a new one in the store and install it in the system.

Breakdown of the

control unit If the washing machine is constantly drawing water and the electronic control unit is the reason for this, then it is necessary to consult with a professional. It is not necessary to independently engage in its inspection and repair. You can finally break the electronics, if you do not have the necessary knowledge and skills. If there is a breakdown in the control unit, then most often it is not repaired, but a new one is installed.

If your washing machine is constantly pumping water into the tank - then this is a serious breakdown, at which it is impossible to use household appliances. If it is not timely to figure out what causes the wrong work, then you can wait for the washing machine to fail completely, and its repair will become very costly, or even impossible. Therefore, when you first call, immediately start looking for the cause of the breakdown and how to fix it.