How to hammer a nail?

1. If there is not so much experience in nailing, then it will not be superfluous to first to apply the marking of and with a pencil to indicate the place of the future fastening. Further, the nail is leaned against the target point with the index finger and thumb at the base, and the little finger is pressed against the surface for greater stability. It is necessary to start with with gentle movements in order to drive a nail 3-4 mm into the surface, and when it is already holding, you can proceed to stronger blows. Professionals say that the fewer strokes, the more nail will sit, so try to aim better at the nail head, and holding the hammer at the end of the handle( so the blow will be stronger and require less effort), make a pair of hand and then2-3 strong elbow strikes.
2. When driving a nail, you need to ensure that it exactly and correctly entered the surface of the .And if something goes wrong, it is better to take the pliers and gently, with rotating movements, pull it out. Do not swing from side to side, otherwise the hole may become very wide.
instagram viewer
3. Probably, many newcomers in the issue of nailing are concerned about the safety of the fingers of the , after all, keeping them at the bonnet with a not too precise blow means getting injured. Therefore, the first time you can use improvised means to hold the nail: it can be a regular clothespin, a comb or even pliers. By the way, the latter will help and if you want to drive with a long nail, , so that it does not bend: just hold the product around the cap with them.
4. If you work with with thin wooden boards , then it is likely that a nail is cracked when driving a nail. Therefore, it is better to choose nails with a core diameter that is 4 or more times smaller than the thickness of the board. As an alternative, do not use nails that are too sharp, and use a nipper to bite off the tip before blocking: this will allow the nail to crush and tear the wood fibers without creating a crack. Naturally, nailing very close to each other on a wooden surface is not recommended, otherwise cracks can be caused.
5. When fastening is necessary to perform near the edge of the board, it is better to pre-seal it with a hammer and a punch. By the way, the piercer is simply irreplaceable, when you need to drown a nail into the surface for further plastering, because if you act only with a hammer, you will get dents. If two boards need to be connected at a right angle, using a few nails, it is better to connect the boards with a small margin, and cut off the surplus after driving nails.
6. It is important to choose with a nail of suitable length : it should be at least one third, and preferably 2/3, enter the surface to which it is fixed. If the nails at an angle of , then the reliability of the connection increases.
7. Experienced master builders advise before driving a nail in general to place it for a short time in oil or soap solution : this will work easier, because the nail will be much easier to enter the surface.
8. When you need to drive a nail into the wall with wallpaper, then there is a high probability of deforming the finishing layer with careless movements. Therefore, it is better to start a small cross-shaped incision before the beginning of driving, at the intended location, and only then begin the main actions. After the nail was set in the right place, the edges of the wallpaper are carefully glued.
9. The nailing process itself reaches automatism very quickly, and problems can arise only when works with hard-to-reach places, for example, when it is necessary to install a fastener in a recess, in a corner, etc. In this case, a steel core and a metal tube will come to the rescue, with which the process is simplified to the maximum: the tube is put on the nail and the core rests on the cap, and then proceed as usual, striking the hammer with the hammer. Instead of a tube and core, you can use a nut with a diameter slightly larger than the nailhead and a bolt. If it is necessary to drive a nail into a spring-loaded bar, then you can use a clamp and use it to press a nail, or use a massive hammer as a support.
10. If it turned out that has a nail that is too long , and its end has already appeared on the reverse side, then, in order to avoid injury, it is better to bend it with a hook, and then drive it into the same surface.
11. Often nails have the property of to bend and even break .There are several reasons for this: too strong or inaccurate blows, or too hard surface. Therefore, if you need to create an mount in an concrete or brick wall, it is better to use a dowel. So, on the concrete wall, the necessary place is planned first, and then a necessary hole is drilled using a perforator: the diameter is indicated on the storm, which should be the same as for the dowel. The depth of the hole should be slightly greater than the length of the dowel. Then they clean the dust, plug the dowel and set the nail. A brick wall can be drilled with a hammer drill, and it is advisable to make a hole in the center of the brick, because the masonry mortar is not a reliable place for fastening.

Contents

1. What tool is needed?
2. Secrets of the correct hammering of nails
3. At the end of

It would seem that it could be easier than hammering a nail. On the question of how to do this correctly, any man should know the answer, and a decent part of women. But in light of the problems of cracked boards, cracked plaster, bent nails and injured fingers, the process of hammering nails is no longer so simple. You just need to know some rules and nuances, and then this procedure will not cause any problems.

So, the secret of a correctly hammered nail is very simple: it is a combination of a well-chosen tool, technique and experience. And if you don’t have enough of the latter, then it's time to get acquainted with useful tips on this topic, which real masters have been saving for many years.

What tool is needed?

A malfunctioning hammer becomes a very common mistake when nailing. It is worth remembering the simple rule that the larger and longer the nail, the bigger and heavier the joiner's hammer should be. Depending on the size of the nail, a specific hammer size is chosen from the four existing ones:

• MCT-1 with a 25-28 cm grip, a 9 cm working part and up to 250 g weighing the smallest nails up to 4 cm in length;
• MCT-2 with a 30-32 cm handle, a working part of 11 cm and a weight of 500 g can be used to drive larger nails. This is the most popular tool;The
• MST-3 already weighs 800 grams, and in terms of the other parameters and the field of use, it hardly differs from the previous version;
• MCT-4 with a handle of 35-37 cm, a working part of 13 cm, and a weight of about 1 kg hammer in nails of 8 cm or more and even dowel-nails.

Of course, with the help of the SME-4, you can also hammer in a small wallpaper nail, but it will be more comfortable to work with a tool with adequate dimensions. But, if there is only one hammer in the house, and you need to hammer in a single nail to hang the picture, then it is unnecessary to bother too much - another thing is if the volume of construction works is more ambitious.

Secrets of the correct hammering of nails

The nail will ideally enter the surface, do not deform it and do not bend itself, and the hammer will not cause injury if you follow a few simple tips.

In conclusion,

Perhaps these are the basic rules that should help the beginning master correctly and without problems, injuries and damage to hammer nails. If you need to pull out a nail that has already been hammered in, you can pry it with a nail puller or a screwdriver, and then pick up the cap with pliers and pull. In this case, under the tool it is better to put a piece of wood, so as not to leave visible dents on the surface.