How to make a kitchen corner with your own hands: diagrams and drawings

click fraud protection
Average time to read It takes ~ 3 minutes to read
Soft kitchen corner
Not many can boast of the presence in the kitchen of free space for oversized furniture. In small kitchens, every centimeter is of great importance, especially in the area where the table is located. In the kitchen you always want to accommodate as many seats as possible. It is quite possible to cope with such a task with a soft corner sofa, which will allow you to use the space to the maximum. At the end of the article you will find a drawing of the kitchen corner, a diagram and step-by-step instructions that will help you to make it yourself.
Kitchen Area

Soft corner with shelves from Ikea

To minimize carpentry, you can use ready-made shelves from Ikea as a frame. To make such a corner with your own hands, you will need materials:

  • Particleboard or plywood.
  • Ikea shelves with facades.
  • Upholstery fabric.
  • Furniture foam.
  • Electric jigsaw.
  • Drill.
  • Construction stapler.
  • Bolts and nuts.

Frame installation and fastening

How to assemble a corner yourself
When choosing the size of the shelves, one should take into account such standards as: the height and depth of the seat should be 40–45 cm. The convenience of using shelves is that you can easily create not only a L-shaped design, but if space and area of ​​the kitchen allow, then a U-shaped.
instagram viewer

By means of bolts, all structural parts are interconnected. But before that, you need to drill holes of the appropriate size in the side walls. If the drill does not fit in the shelf, then the hole should be drilled from the outside, separately in each wall. It is very important to make clear measurements so that there are no problems when connecting the structure.

In order to prevent the wood from deteriorating with strong tightening of the bolts, it is recommended to additionally use gaskets for the caps of the bolt and nut.

Installation of facades and seat bases

After the frame is installed, the facades of the shelves must be fixed. You can do without this, which will make the design much cheaper, but if you need additional space for storing various things, then you still need to install the doors.

The basis for the seats is created from sheets of chipboard (OSB) or plywood. Plywood with a thickness of 10 mm and more can withstand high loads and has good moisture resistance. The most economical option is to use a wood-particle board or oriented particle board.

The board is cut to the size of the corner with a jigsaw. Next, sand the edges with sandpaper of medium grain size.

Upholstery with soft material

Corner mounting
This stage of work is the most time consuming. Furniture foam should be cut in the same way as a plywood sheet. Then it is glued to the base.

It is important to use a special glue in the work, designed for strong bonding of foam rubber with a wooden surface.

The next step will be covering with fabric using a construction stapler. The distance between the brackets should be 1-2 cm. Even a person inexperienced in this matter will be able to upholstery with plain material, but you will have to get used to the complex pattern, because this task is no longer easy.

The finished seat can be supplemented with soft pillows, which will also serve as a backrest.

Simple kitchen sofa do it yourself from the furniture panel

Corner layout
A DIY kitchen corner from a furniture board is one of the most budgetary options for this venture. For work, you need such materials:
  • Acrylic paint.
  • The cloth.
  • Drill.
  • Jigsaw.
  • Wood screws.
  • Furniture panel (18 mm).
  • Foam rubber (80 mm and 20 mm).

Cutting the shield and fastening parts

Before proceeding with the cutting of the shield, it is necessary to draw up drawings of a home-made kitchen corner with cuts. The project must be designed in such a way that at least 3 people can freely sit on the couch.

It is better to start cutting the shield with a jigsaw, but you can do with a hand hacksaw. During the cut, the tool should be held strictly perpendicularly, and the ends of the shield should be located strictly at an angle of 90 ° in relation to the main plane.

The parts are fastened with self-tapping screws, and in order not to form cracks, you must first make a hole for the screw. The diameter of the drill should be 0.5-1 mm less than the diameter of the self-tapping screw.

Body painting

What materials will be needed
For painting, you can use alkyd enamel or acrylic. It is better to opt for acrylic enamel, due to its stability, durability and lack of a pungent odor, which will allow the use of enamel directly in the room.

Before painting, it is necessary to treat the surface of the body with a primer to increase adhesion between the varnish and the wooden surface. We make a coating in 2 layers, and for a more saturated color - in three.

Making soft pillows

For sewing pillows we use foam rubber, which, unlike sintepon and holofiber, has a more improved density and it is more comfortable to sit on it.

For the back, you can use thinner foam, and for seats you need foam rubber with a thickness of at least 80 mm.

If it is possible to work on a sewing machine, then it is best to sew removable covers with zippers or buttons. This option is convenient in that the old fabric can always be replaced with a new one without extra costs.

DIY kitchen corner made of wood

A very simple, but original corner for the kitchen can be made from a wooden board with your own hands. To work, you need:

  • Foam rubber.
  • Wooden board 100x40 mm.
  • Plywood or chipboard.
  • Round dowel with a diameter of 15 mm.
  • Drill with a crown of 15 mm.
  • Jigsaw.
  • Construction stapler.
  • Batting.
  • PVA glue.
  • Upholstery fabric.
  • Varnish and stain.

Sawing and grinding parts

First you need to create a drawing on paper or in a special program, and then you can start cutting the board into parts. To give the corner a more elegant look, you need to carefully cut out the curly details with your own hands. To make the elements smoother and more accurate, using a flexible ruler, you need to draw lines on the surface of the tree.

All parts are sanded several times with sandpaper of varying degrees of grain. Following, according to the drawing, the whole corner is assembled using dowels and glue.

Staining and varnishing

DIY corner
Instead of enamel, a stain is best used. The stain does not create an unnecessary film effect on the surface of the tree, but, on the contrary, retains its structure. Color can vary from light to dark red. The stain has a peculiarity - to raise the pile of the tree during the painting process, therefore, after drying, it is necessary to polish the surface again.

Like stain, varnish should be applied in several layers. To speed up the process, you can use water-soluble varnish, the drying time of which is no more than 30 minutes.

Frame assembly

Before using the glue to fix the ends of all structural elements, it is recommended to assemble it “dry”. It must be ensured that all parts of the frame are fitted without gaps.

If everything works out fine, you can start assembling the frame with glue. For reinforcement, you can use metal corners 4x4, which are attached to the inner corners.

The bottom of the boxes can be made of plywood or from a sheet of chipboard. The selected material can only be put on the furniture corners attached below to the frame.

Seat mounting

From the same sheet of plywood or chipboard from which the bottom for the boxes was cut, you can make the base for the seat in size, which is indicated in the drawing. Working process:

Step 1. We take the foam rubber and cut out a piece of it, which should be 2-3 cm larger than the base from all sides.

Step 2 Glue the foam to the chipboard.

Step 3 Cut the batting along the contour and glue it to the seat with the same glue.

Step 4 Using a construction stapler, we attach the upholstery fabric.

It turned out an excellent corner sofa, which can become an adornment of any kitchen.

How to make an original corner sofa from pallets

Kitchen corner
The direct use of wooden pallets transportation of goods. But this simple design can serve as a reliable material for the manufacture of furniture.

It’s possible that such a sofa will not fit in every kitchen, but it’s also perfect for a gazebo in the garden, especially since a sofa made of pallets is not particularly difficult to assemble.

Selection and adjustment of pallets

First of all, you need to inspect the pallets that will be used for the manufacture of furniture for chips and damage so that there are no troubles during operation.

The size of the pallet is designed corner sofa. If space allows, you can make furniture from solid pallets, otherwise you will have to resort to using a circular or hand saw.

Connection parts

Making a corner for the kitchen or gazebo is not difficult, because for this you just need to connect the finished parts to each other with screws.

It is recommended to install pallets in two rows so that it is comfortable to sit, taking into account the fact that there will still be a layer of foam rubber or a thick mattress on top.

To make the backrest, it is necessary to attach the pallet in an upright position to the base. This completes the assembly.

Photo - a homemade kitchen corner: drawing and dimensions, diagram, step by step instructions

How to assemble a corner with your own hands
Materials and tools for the corner
How to make a corner yourself
Materials for creating a corner
DIY corner
Kitchen Area
How to make a corner

With great interest I always read your comments to my articles. If you have any questions, feel free to ask them, leave, you are welcome, Your feedback in the form below. Your opinion is very important to me. Thanks to your criticism and thanks, I can make this blog more useful and interesting.

I would be very grateful if you rate this post and share it with your friends. This is easy to do by clicking on the social media buttons above. Do not forget the article you like Add to bookmarks and subscribe to new blog posts on social networks.

Wall mural for the kitchen: photo in the interior, types, selection rules

Wall mural for the kitchen: photo in the interior, types, selection rulesRepair Of

It takes ~ 2 minutes to read Often, the design of the kitchen looks monotonous and meager. Being in such a room, for example, in the morning, we will not receive a charge of positive emotions f...

Read More
Original decorative brick walls in the interior of the kitchen

Original decorative brick walls in the interior of the kitchenRepair Of

Russia, Moscow region, Moscow+79041000555 It takes ~ 2 minutes to read There is a popular belief that brick can only be used for the construction of capital walls. However, today decorative ...

Read More
How to choose facades for the kitchen: comparison of materials, photos

How to choose facades for the kitchen: comparison of materials, photosRepair Of

It takes ~ 4 minutes to read When it comes to decorating the kitchen, the first thing the tenants think about is the facades for the kitchen. And not surprisingly: this furniture set is decisiv...

Read More
Instagram story viewer