Holders of juicers often wonder how to disassemble the kitchen unit correctly -. Ie. without compromising its functionality. The need for parsing appears in violation of normal functioning of the device, because some problems can be resolved on their own, thereby saving the budget.
Common causes when there is a need to disassemble the juicer
The content of the article
- Common causes when there is a need to disassemble the juicer
- What the components of a juicer
- Required tools and stages of disassembly
Identify several main reasons for failures in the juicer:
- liquid spills into the equipment;
- jump occurred power supply;
- load is exceeded due to the long time of the juicer.
About breakage may report the following signs:
- excessive heating and sparking equipment - squeezer needs replacement of certain parts;
- slow shaft rotation - most likely it will be necessary to clean or replace the bearings;
- captured the smell of burning, there are traces of black on a juicer - this happens when burnt coil products - in this case it will only be replaced.
These are the main causes of failure and how to resolve them.
IMPORTANT! The burned motor winding - the most serious fault - the rest is easy to fix at home.
What the components of a juicer
Absolutely any juicer standard set of components in the kit:
- motor;
- Products cover;
- pusher products;
- utensils for collecting the juice of fruits and vegetables;
- strainer and insert under it;
- dishes to collect vegetables and fruit cake.
Required tools and stages of disassembly
For disassembly of all kinds of such equipment does not need a lot of tools: need a standard set of screwdrivers of various shapes and types. Main Circuits juicers are fixed on the latch, screws and clamps may need more tools with complex damage, but their advance is not necessary to prepare, as with the complex breakdown better to turn to specialists.
Before disassembling the juicer should definitely switch off the appliance from the wall outlet and move the switch button in the shutdown mode. Once the machinery stops working and make a noise, you are ready to get started. It is necessary to remove the plastic plunger from the tank load of fruit and vegetables. Remove the container and the waste cake. You should also make sure that all the juice flowed out, you have to tilt forward and technique over and disconnect the liquid tank.
Subsequent stage of disassembly of the device is a careful study of the attached instructions. Do not rely on "maybe" and do everything at random, as this may lead to even greater problems, and it is impossible to do then to repair the juicer. Technology can be applied to the defect, which simply can not be eliminated.
REFERENCE! Almost all of the instructions are similar to the technique, you can download them from the Internet.
After studying the instructions necessary to proceed with the removal of the top cover and all retaining elements. They are either firmly inserted into one another, or attached to special plastic or metal clips, that is, it is necessary to remove all that is fixed without the use of tools and that can prevent the dismantling of the motor juicer.
To remove the motor unit and mounts it is necessary to remove the flip technique upside down and unscrew the four bolts on the bottom. Then remove and remove all mounting pads electrical wires from the back side of the unit. Thus, the bottom is completely free - it can be removed to the side.
After all these manipulations removed disk drive with the shaft equipment. This should be done by holding the piece from turning in the opposite direction, by disconnecting the bolts and nuts. Another way is to raise it up, if he just firmly planted on the shaft itself without the use of nuts and bolts.
The next stage is the removal of the motor housing. You need to remove all the screws and bolts that prevent the removal of directly switching the handle and release all the wires. Also unscrew all the bolts of the engine control board juicer and set aside.
After all procedures easily unscrew the screws of the motor and take it out.
it is necessary to remove the motor rotor for inspection equipment and disconnect all cables, and then extract the necessary detail and inspected for faults and damage. It is also advisable to check the bearings, having turned them a couple of times with his finger. If all goes well, the rotor has to move by inertia without difficulty.
Juicer has earned to be treated it from dirt and dust, to inspect. Rang a special device all cables, motor windings and other elements of the board.
