prom.ua
If you are interested in what is "living" and "dead" water, what are electric activators for water and their design, then read on - about "living" and "dead" water, the first production of "living" water, the design of electric activators, how to use.
"Living" and "dead" water - what is it. Modern concepts of "living" and "dead" water appeared relatively recently. However, in fairy tales, traditions, legends, ancient textbooks, manuals, these concepts were often mentioned. “Living” and “dead” water gained particular popularity in the Middle Ages, when it was believed that they had magical and special healing properties. But what is "living" and "dead" water in the modern sense? One of the oldest recorded ways to obtain "living" water was as follows:
The first step is to hold drinking water for several hours in a dark room so that it settles. Next, it must be boiled and quickly cooled. For cooling, snow / snowdrift was used (“living” water was usually prepared in winter) or ice was added. After water, you need to insist on silicon. During this time, harmful impurities will settle to the bottom. The water was again poured into another container, without touching the unnecessary bottom layer. The drained water was frozen. When the first layer of ice appeared on it, it was removed and thrown away. Then the liquid was frozen again, but only by two-thirds. A hole was made in the newly formed layer of ice, through which the finished liquid was poured. The result was pure water with a high concentration of salts.
Today, it is possible to make “alive / dead” out of ordinary water in an hour or less. To do this, use specialized devices - electroactivators. In the CIS countries, the AP-1 activator from the Belarusian manufacturer Aquapribor received the greatest popularity.
What is "living" water in the scientific sense. It is water with low acidity, alkaline structure and a large amount of salts. Such water is called catholyte. Such water is stored without loss of its properties for up to 7 days in a completely sealed container in a dark room. "Living" water accelerates biological processes - metabolism, digestion, regeneration / healing of tissues, stimulates the immune system. Because of this, it is recommended to use it in almost any case - to improve appetite, with serious wounds, to increase blood pressure, as well as to prevent and stimulate immunity in healthy people.
What is "dead" water in the scientific sense. In turn, "dead" water is the opposite of "live". It has a positive potential, a low salt content and an acidic structure. The official name in the scientific community is anolyte. If the catholyte accelerates biological processes, then the anolyte slows them down. Because of this, "dead" water can be used as an antiseptic or preservative. It is recommended to be used for muscle/joint pain, cramps, bowel disorders, skin disease, and also as a prophylaxis for colds.
The design of the activator for water. Structural elements of any electric activator for water:
prom.ua
- Main plastic tank
- quartz glass
- Power supply and its wire by wire
- Lid with 4 electrodes attached
To use such units, you will need water from which catholyte and anolyte will be obtained, the electric activator itself and a household outlet (classic voltage 220 Volts).
Before buying an electric water activator, make sure that the device is fully certified. The kit must contain a certificate indicating the second or higher class of permitted combination. water with electricity (according to the state standard) and a document confirming the hygienic security.
A non-original device without these documents may harm your health.
Step-by-step instructions for using the AP-1 water activator. Detailed instructions for use are attached to the device itself, which describes how the device works, how to take care of it. The instructions also explain what the acidity of water is, what pH value is better to use in specific situation (table with concentration dependence) and how to get a specific value acidity.
If you have lost the instruction, then the following data will be for you:
pH is how acidic the water is (how much hydrogen it contains). The indicator of ordinary drinking water is within 7-8 units. "Living" water, accelerating biological processes - 8-10, "dead" - 3-6.
How to use the AP-1 water activator, how to use the water activator. First of all, you need to remove the top cover of the device with the electrodes on it. After that, place a ceramic glass inside the container, placing it in the center. Next, pour ordinary tap water into a glass, you need to completely fill it. After that, it is necessary to pour all the same water into the container itself, but the water level in the container should be 1-2 centimeters lower than the height of the glass. Put the cover of the electric activator back in place. Make sure that the pointer arrows are located directly opposite each other, black sticks (anodes) should be inside the ceramic glass, while light sticks (cathodes) should be outside, in a plastic containers. At the end, you just need to insert the plug from the power supply into the socket (voltage 220 Volts) and remember the time when you turned on the activator. After 10-50 minutes, the device will finish concentrating the water, and in the end you will have "live" and "dead" water. Several special indicators that are located on the electrodes will signal the completion of work.
Longer operation of the electroactivator will provide a more concentrated water solution. In different cases, water of different concentrations is more suitable.
After completing the operation of the electric activator, first unplug the plug from the socket. Then carefully remove the top cover of the device (it must not be turned over, because this may violate the correct position of the electrodes - the activator will not work correctly). Remove the ceramic glass from the container and use the water for its intended purpose.
In a ceramic glass there will be "dead" water, in a plastic container - "live".
