How to Use a Laser Level: How It Works, Proper Use and Storage - Setafi

There are several basic ways to use a laser level. The device is installed on the surface, turn on and project the beam on the floor, walls or ceiling. They make outlines, after which they lay tiles or put up a wall. The level can be used for a variety of tasks. The main uses are described in this material.

Preparatory stage

Before starting work, it is important to properly prepare the tool. Before you understand how to use the laser level to level the floor and other surfaces, you should perform a few steps:

1. Remove all obstacles that may arise in the path of the beam.
2. Place the device so that the distance to the object is within the maximum allowable value specified in the instructions. If necessary, this distance can be increased using a special receiver.
3. Fix the tool on a flat surface. Here you need to understand how to work with a laser level so that the error is minimal.
instagram viewer
4. Align the instrument along a horizontal line. To do this, they are guided by the built-in level with a bubble; in some cases, the devices are equipped with a self-leveling function.

To understand how to use the laser level correctly, you need to know about the principle of its operation. The level is particularly accurate due to the work of a concentrated beam. Therefore, it is necessary to observe safety precautions in order to save the eyes of yourself and those around you.

How to use the device

Several basic techniques have been developed on how to use a laser level. After the setup is completed, you can proceed directly to the measurements. Recommendations for different occasions (e.g. wallpapering, tiling) are described below.

Wall alignment

The main instruction on how the laser level works is related to the use of a device for leveling walls. The device is installed next to it, literally 3-4 cm, and the beam is directed exactly along the wall. Then carry out measurements of deviations. To do this, use a ruler installed strictly perpendicular to the laser.

They get the necessary figures for deviations and calculate how much plaster is suitable for this case. The procedure is quite simple. But in order for the measurements to be as accurate as possible, a device with a laser head located in the lower part of the case should be used.

Laying tiles

If you learn how to use the laser level to level the walls, you can lay the tiles with high quality. It must be placed strictly perpendicular, so in this case you will need the option to build planes.

Laying can be carried out using a laser beam. In this case, the tool is left on all the time. Pre-check the battery level or install new batteries. If we talk about how to use the laser level for the floor, the principle will be exactly the same.

On the other hand, you can use a special marker or pencil with which to put the markup. This will save battery. In addition, the beam will not interfere with the eyes during operation. In order to correctly evaluate how to use the laser level, after the installation is completed, you can turn on the device again and check the result.

Wallpapering

Since the principle of operation of the laser level is associated with the use of a beam, which allows for great accuracy, it can also be used for wallpapering. The instructions are exactly the same. You can turn on the beam and leave it on all the time, or make a few notes with a pencil, and then proceed to wallpapering. At the end of the work, you can check the results by reconnecting the device.

Furniture assembly

Another option on how to use the electronic level is related to the installation of furniture. To properly install hanging boxes, you need to outline several beams in a horizontal plane. Then it will be possible to carry out measurements with a minimum error.

Partitions

In rooms, partitions are often constructed using drywall sheets. In this situation, it is also useful to study the algorithm on how to use the laser level for walls. To make an even partition, proceed as follows:

1. Direct the beam to the floor so that it is parallel to the opposite wall (relative to the partition that is planned to be installed).
2. The laser level device allows you to accurately outline the desired lines. Do this with a pencil or marker. Tags are recommended to be set at intervals of 20-40 cm.
3. Then they are connected with straight lines to form a single network.
4. After that, with the help of a level, the same lines are transferred to the ceiling.
5. At the last stage, a projection of the wall is made on the surface of the ceiling at similar points.

In the described case, it is quite simple to understand how to work with the laser level correctly. Moreover, to obtain more accurate outlines, it is better to use a device that can build a 360 ° plane.

Foundation laying

After pouring the foundation, you should determine how well the work was done. In these cases, it is also useful to know how to use a laser level. The sequence of actions is as follows:

1. The device is placed right in the center, aligning its position.
2. The rod measures the distance to the beam at each corner. They make notches.
3. Next, the results are evaluated. This will help knowledge of the device and the principle of operation of the laser level.
4. If the deviation lies within 1 cm for every 10 m of base, this is an acceptable error. But if it exceeds 1 cm, refinement should be carried out.

The use of a laser level does not raise any special questions - even a beginner will be able to figure out the instructions in a few measurement procedures. At the same time, in the professional field, and often at home, the tool is used simultaneously with additional accessories.

In practice, an optical sight, laser receivers, tripods and rails are often used. Thanks to this, the speed and quality of measurements are noticeably increased if you know how to use the laser level correctly. At the same time, it is necessary to observe safety precautions, work in protective glasses and prevent strangers.