This manual is designed as assistance in the search for breakdowns and solving problems related to the breakdown of dishwashers "Gorenie".
Often happens that the error on the MMP display appears due to the failure of any part, and its the solution requires repair, and not only the entrance to the service test, which the master conducts with the primary diagnostics.
Next, we will consider the main mistakes of Gorenje dishwashers and give brief comments that will help in troubleshooting the malfunctions indicated by this or that code.
How to decode trouble codes dishwashers "Gorenie"
First, let's look at how errors are displayed on models with an LED panel and with LCD displays. Depending on the model of the dishwasher, it is necessary to decipher what the alphanumeric code or a certain combination of light bulbs means.
| Troubleshooting codes | What kind of light bulbs | Value |
| E1 | Triggering of leakage sensor. Receipt of water in a special tray (when the dishwasher is equipped with such a detail). | |
| E2 | The overflow sensor is activated. | |
| E3 | Lack of water heating. | |
| E4 | A break in the operation of the thermistor. | |
| E5 | No gulf in the dishwasher system. | |
| E6 | No plum. | |
| E9 | This code indicates the same as error E2. |
Values of error codes and recommendations for troubleshooting Gorenje
Below, we list the codes for the fault codes that a user may encounter when operating a Gorenie dishwasher. In the tables below, the reasons are presented in the form of a rating: starting from the problem with the highest probability and ending with the least.
E1 - activation of the leakage sensor and detection of water in the pallet container
Appears if the float sensor of the "Leakage Protection" system is closed for more than 3 minutes if water seeps into the pan. In this case, the pump will work until the contact of the element is opened.
| Cause | How to fix |
| The water is trapped in the drip tray due to the leakage from the Aquastop system hose in the tank. Also, the internal components of the housing - the pump, recirculation pump, etc, can flow; connecting branch pipes. |
Empty the sump to open the capacitor filler contact. After this, the dishwasher must be reset to check and locate the leak. The leakage is eliminated, and the machine can be used. |
| The fill sensor is stuck. | It is necessary to open the sensor, returning it to its working position. |
| The overflow sensor broke. | The sensor needs to be replaced and the dishwasher reloaded. |
| Gaps in the wiring. | It is necessary to check the wiring, connectors and contacts of the leakage sensor, the system board. Damaged wiring areas require maintenance. |
| Breakage of the control unit. | The malfunction in the operation of the electronic board is obvious, if none of the four breakdowns mentioned above has been confirmed. How to reboot the machine to determine the module failure: · Start the dishwasher; Select the washing mode; · Close the loading hatch; · If after 3 minutes or less the PMM shows the error code E1, then the problem is still in the block and its replacement is required. |
E2 - the sensor of the level of the dishwasher "Gorenie" was triggered
The system signals an error E2 if the water level has crossed a certain mark and the overflow is fixed. The "Burner" dishwasher stops the user program, starts the pump to drain the water, and displays an error on the display (or the indicators flash).
Important!To immediately exclude the failure of the control board, you need to perform this check:
- Remove the side wall and check if the pan is full (the float might have worked).
- Drain the water from the dishwasher, emptying the tank.
- Disable PMM, disconnect the blue wire from the pressure switch connector.
- Turn on the machine.
- Enable the program number 1.
- After starting the program, the following situations can occur:
1. The drain will start. This will mean that the electronics have correctly determined the signal and worked, which means that the control unit is OK.
6.2. PMM will start pouring water into the system. This means that the electronic system misinterpreted the signal, the control unit failed and needs to be replaced.
| Causes of error | How to fix the problem |
| Incorrect installation of pressure hose to level switch. | The rubber hose needs to be checked: it may contain tears or breaks. If there are breakouts in the hose, there will be a loss of pressure, which means that the element will not be able to perform its functions. |
| Water has entered the pressure supply hose to the level switch. | In this case, you need to detach the hose from the sensor and inspect if there is water in it. If there is, the part needs to be changed to a new one. |
| The level switch is out of order. | After emptying the dishwasher tank, check the operation of the pressure switch, use an ohmmeter. If the relay needs to be changed, install a new part. |
| Breakage or clogging of the washing pump. | Select the mode and turn it on. Make sure that the pump evenly feeds water without creating bubbles. If water is supplied intermittently, it is necessary to inspect the pump hose that passes through the drip tray - there may be clogs. If the problem has not been solved, the detail needs to be changed. |
| At the intake valve, the rate of water intake is exceeded - the rarest cause of this error. | Repair consists in covering the water tap to adjust the water flow pressure. After that, reboot the device several times to make sure that the problem is solved. If code E2 lights up again, then the inlet valve has to be replaced. |
E3 - no heating
Signal lights or an error code are lit on the user panel when the water is warming too slowly - less than one and a half degrees in 20 minutes.
| Causes | How to fix |
| Operation of the heater thermal protector (if provided in the design). | Using a tester, measure the resistance of the fuse. If "0" is lit on the device's screen, it means "closed no operation. If the measurements report: "open the fuse has tripped to protect the heater from overheating and burnout. In the latter case, the operation of the thermal fuse is due to one of two possible causes: 1. The position of the thermistor is broken. 2. The washing pump was deformed. |
| Broken TEN. | The heater should be checked using an ohmmeter. Measure the resistance by attaching the probe to the terminals. The normal values are within 25 ohms (at room temperature of 20 degrees). If the meter shows a "break it means the heater fails and needs to be replaced. |
| Incorrect installation of thermostat. | Check that the thermistor is correctly installed by adjusting it in the socket. Replace if necessary. |
| The integrity of the wiring is broken. | Carry out wiring maintenance by checking the integrity of the connections on the dishwasher parts and its control module. Use the tester: measure the resistance by applying the test leads to the board connectors. After finding damaged areas, repair them. |
| The impeller (sprinkler) stopped rotating. | Check that the element rotates freely. If something hinders him, the heat is distributed incorrectly. |
| The washing pump is broken. | If the washing pump stops working, the water stops circulating in the system, so it does not warm up (at this point, the heater thermal protector could work). It is necessary to replace the pump and fuse. |
| Control unit failure. | If the above failures are not confirmed, it could mean that the relay controlling the operation of the TEN was broken. Using an ohmmeter, measure the voltage on the heater connector when it is heated. At this point, the terminals must output 220 volts. The voltage control should be kept for a couple of minutes, because the heater is not started immediately after switching on; To diagnose a breakdown, you need time. If the failure is confirmed, you need to replace the module. |
E40 - Thermal sensor circuits are cut off
This code you will see when the PMM and the sensor is not working. The fault is rare if the operation of the dishwasher is correct. Failure often occurs as a result of previous repairs - maintenance of the wiring or replacement module, detergent cuvettes.
To solve the problem with your own hands, try to apply our recommendations.
| Cause of malfunction | How to fix |
| The integrity of the wires is broken. | Check the reliability of the wiring and its connection to the electronic board. If you find defective areas, perform maintenance. |
| The thermistor is broken. | Armed with a multimeter, measure the resistance of the thermostat - it should be at a level of 12 kΩ at room temperature values of 20 degrees. If an open circuit is detected, this means a breakdown and the need for a replacement. |
| The control unit does not receive signals from the thermistor. | If the previous reasons are not confirmed, and the control unit does not reach the sensor, it is most likely a problem in the electronic board itself. It needs to be changed. |
E5 - dishwasher does not fill the water
This code usually lights up when dialing in the dishwasher water, if the required level is not reached in a 7-minute period.
| Possible problems | How to fix |
| The valve on the water supply pipe is blocked. | Try opening the tap. |
| The hose of the bay is clamped or twisted. | Check if the hose of the bay is clamped in the PMM. Also inspect the filter mesh on the body of the machine, at the inlet of the hose. Spread or install the correct hose. At the same time, rinse the filter net. |
| The contacts in the intake valve circuit are broken. | Check the integrity of the connections between the intake valve and the electronic board. Run the tester in ohmmeter mode to measure the resistance and check if the connections are OK. Find damaged areas, provide them with repair. |
| There was a break in the coil of the water intake valve. | It is necessary to check the coil with a tester. If a breakage is detected, the valve is broken and requires replacement with a similar one. |
| Block failure. | If the wiring is all right, take a tester to check the voltage on the solenoid valve. When the gulf is powered, the parts must be at 220V. If there are no indicators, then the module needs to be changed. |
E6 - no discharge
The alarm code "E6" lights up when draining, if the tank does not empty within three minutes.
| Failure | Troubleshooting |
| The position of the drain hose is violated. | Check that the hose is correctly installed - it may be clamped or twisted. Install the hose so that it is free. |
| The pressostat is broken. | Drain the water from the PMM, measure it with a tester, how the level sensor switches. If a problem is found, change the pressure switch. |
| The drain pump is broken. | Check the operation of the drain pump. You will need a tester to check the resistance on the connector, where there should be no breaks. If the pump's winding is broken, the pump is broken and must be reinstalled urgently. Sometimes the pump stops draining at normal ohmmeter. Replace the pump if you can not find the cause of the fault. |
| Violation of the integrity of the wiring leading to the pump. | Make sure that the connections (wires) of the part are in order. Check the tester and repair the damaged areas. |
| The control unit has failed, stopping the pump or receiving signals from it. | Check the tester if the pump receives voltage from the side of the unit when draining - there should be an indicator of 200V. If the work of the part is not broken, but the signal does not reach the module, that the tank has already been emptied, the electronic board may not be damaged. Both cases require replacement of the unit. |
E9 - overflow
This code requires a complete check of the hydraulic system of the dishwasher "Burning". Pay special attention to the situations listed in the table.
| Cause of failure | How to fix |
| The water in the hose of the priming system is drained. | Eliminate the same as for E2 code. |
| The water went into the pressure sampling chamber from the pressure switch. | It is necessary to change the pressure selection system to the analog of the last modification (it must have a yellow stamp). |
| The washing pump is broken or clogged. | Start the washing mode to check how evenly the water flows. Do not exclude blockage of the pump hose. It is necessary to remove the clog or change the pump. |
Important! In electronic boards "Gorenie" for 3 and 5 buttons (the first generation of screens) the code E9 does not light up.
Now you know everything and even more about the mistakes of Gorenje dishwashers. You will be able to provide feasible first aid to the affected equipment and save on diagnostics when calling the master.
