Why is a washing machine jumping or vibrating while spinning

Do not know what happened to your washing machine, because of what she started to jump, strongly vibrate and make uncharacteristic sounds? She may have slipped off her legs or become wrong. But strong vibrations may also indicate a more serious problem that requires immediate attention. So can cause noise. We will try to understand before this problem is aggravated.

Why a washing machine begins to jump while spinning

There are a lot of reasons why a washing machine jumps and makes more noise. Let's consider what problems can cause a strong vibration of the washing machine:

• When washing small items can fall between the drum and the tank, for example, sometimes we can wash things with coins, paper clips, bedding with pins or get small buttons and fasteners.
instagram viewer
• If the transportation bolts were not removed during installation.
• Incorrectly distributed underwear in the drum machine( found in older models of washing machines).
• If your motor is broken.
• Washer installed incorrectly on supports.
• Check for bearing failure.
• Faulty or badly worn springs and shock absorbers.
• . Another reason could be a loosening or deformation of the counterweight.

Troubleshooting

The problems are manifold, and it is very difficult to find out immediately what could cause strong vibrations. Therefore, it would be more rational to exclude, at first, the simplest options, the washing machine machine rattles and shakes. What to do to find out the simple reasons why a washing machine jumps during the spin cycle:

• Take a good look at whether the laundry is not wrapped in a knot, it often happens that small items of clothing are clogged in a duvet cover or sweaters.
• It is necessary to check whether the amount of laundry in the machine does not exceed the maximum allowable. For each washing mode and machine models, different acceptable indicators are possible.
• Noise can occur when things take up more than 2/3 of the drum volume.

In such cases, some washing machines are equipped with a special sensor that displays errors on the display such as: UE or UB.

How to install a washing machine so that it does not jump?

Strong vibrations can often be caused by improper installation or typical errors, especially when the equipment is not installed by professionals or installation is done independently. The most common mistake are shipping bolts that simply forget to remove or install the device unevenly or put it on a slippery surface( tile), which causes a wobbling and, as a result, a lot of noise.

Why a washing machine jumps when improperly installed and what to do:

• The first step is to remove the transport brackets. They are set to fix the drum so that it does not get damaged during transportation. If they are not removed, the drum will spin, but its wear will be greatly increased, and the work of the apparatus itself will be accompanied by strong vibration and bouncing.
• Carefully ensure that the equipment is installed strictly on the level. To do this, you can twist the legs and adjust their height. When spinning, the machine enters into resonance and can even move around the room, so it is not recommended to leave the faulty equipment in working condition unattended.
• After the installation, check to see if the device is loose. Any, even the slightest staggering can lead to jumping. If the washing machine machine staggers, then it will have to be leveled.

Even if the technicians are to be installed by professionals, it is better to check these nuances on your own to make sure that everything is in order. Be sure to test the job after installation. Such actions will help you save time on a subsequent re-call of the installers, so that they eliminate the malfunction and do not wonder what to do so that the machine does not make frightening sounds.

. Shock absorbers are faulty.

It is necessary to inspect the shock absorbers, which serve to soften the blows when the drum moves, reduce the loads and dampen oscillations. If the device vibrates or jumps heavily, then the shock absorbers may have to be replaced. Shock absorbers are mounted together with spring mechanisms, but if only shock absorbers are worn out - they can be replaced separately, if the springs are out of order, then you will have to change everything at once. Over time, the shock absorbers wear out and cannot be repaired - they should be changed immediately. Depreciation may be uneven, but if only one is defective, both shock absorbers must be replaced in order to balance the load.

Look, perhaps small things stuck under the drum. If they are, then you have to get them. For example, a bone from a bra or a clip can be easily reached, if you pick something up, you can do something like a hook, which will be convenient to pull out small parts. If you get stuck smaller parts that can not get it - you have to disassemble the washing machine. To do this, remove the heating element, the drum and some other details. If you have never dismantled washing machines, then it is better to call the wizard who will do it as quickly as possible, which will save you decent time, but most importantly, it is safe for the equipment.

Problems with mounting counterweights

If the washing machine began to vibrate and jump heavily, you need to check the work of the counterweight. We open the cover in the upper part of the device, for this you may need tools, it will be enough to use keys, a screwdriver and pliers. We look at the state of the counterweight, it is a weighting agent, which is made from different materials. Such parts are installed at the top and bottom of the washing machine. They can be made of concrete, cast iron, or other heavy material.
What to do next:

1. We look at the mount, if they are loose, you will need to tighten them.
2. If you can not twist the mount, you will have to purchase and install new ones.
3. If the weighting agent itself is deformed, it is impossible to do without replacing it with the same one.

One of the reasons why a machine can jump is a bearing failure. The replacement process is technically difficult, so it’s best to call a master who can do the job properly. If you still want to do it yourself, then you need more information about this process, so you can read about the relevant article.

Bearing Problem

Malfunctions related to bearing failure are not uncommon. The main reasons for the breakdown of this part are due to the fact that the metal from which the elements are made of, over time, is destroyed due to exposure to water. When the bearings begin to deteriorate, the operation of the apparatus will first be accompanied by increased vibration and noise, and then the drum may be completely jammed.

When the bearing is just beginning to fail, it is quite difficult to identify the problems. Usually, professionals can say about the wear of the part on the sound, but for this you need to have experience and knowledge. But when the bearing is already badly damaged, you can move the drum. When he moves in different directions, it says that it is time to call the master to replace the worn bearing.

What can we talk about in the end? It turns out that a washing machine is a complex system that needs professional help to troubleshoot technical problems and you should contact qualified professionals with the experience and knowledge to quickly and effectively fix the problem.