Malfunctions of the Electrolux washing machine (Electrolux): error codes, methods of correction

Each owner of the Electrolux machine should read the manufacturer's instructions, adhere to the rules of operation. In the event of a malfunction, you must use information that will help to fix the household appliance faster.

Basic troubleshooting

Automatic machines are considered one of the most reliable in their segment. Household appliances are operated in harsh conditions: frequent power outages, hard or too alkaline water. Therefore, the failure of equipment is not a critical situation. The Swedish company took care of its customers - each model is equipped with a controller that identifies the alleged error and displays the codes on the display. Knowing these ciphers, one can not only correctly diagnose, but also get out of non-standard situations when, for some reason, during operation of the equipment, a slight malfunction is observed.

The most common failures in the operation of Electrolux machines:

• The appliance does not turn on.
• RCD trips.
• Water does not heat up.
• Water does not enter the system.
• Water does not drain.
• Loud device noise.
• The presence of water on the floor under the body.
• Pump blockage.

If washing machine Electrolux does not turn on, then the reasons may be:

1. Lack of input voltage.
2. Malfunction of wiring, introductory machine or power cord.
3. Damage to the start button of the electrical appliance.
4. Drum damage.
5. Failure of an electronic module or selector.

You can independently verify the health of sockets, wiring and automatic machines. If all the manipulations did not succeed, then you need to contact a service center.

Top-loading Electrolux washing machine not picking up water. Rarely, factory defects can be the cause. Most often, this malfunction of the Electrolux washing machine occurs due to:

1. problems with the drain pump (pump);
2. breakage (blockage) of the inlet valve;
3. failure of ten.

If cleaning the pump or replacing it at home does not correct the situation, then solving the problem is possible only with the help of qualified specialists.

Lack of detergent intake function from the container. A common phenomenon that is eliminated by flushing this element. It occurs due to excessive filling with powder or a long downtime of equipment with refilled detergents in a humid room.

The drum does not spin Cars Electrolux. Occurs for the following reasons:

1. excessive load of laundry in the machine;
2. motor breakdown due to a short circuit;
3. brush failure. The emerging magnetic field prevents the motor from starting;
4. failure of the drive belt. Occurs due to prolonged downtime of the machine.

If unloading the washing machine did not help, further diagnostics at home are not recommended. Although you can disassemble the drum of the washing machine yourself.

If the machine is automatic does not heat waterthen it is necessary:

1. check and repair the thermostat;
2. check the status of ten;
3. Diagnose the network stabilizer.

Loud noise associated with the following processes:

• clogging, jamming of foreign objects in separate nodes of the washing machine. Timely extraction of a third-party item can save from complete failure of the equipment.
• Broken network filter connections. Reinstalling the part may resolve the situation.
• Bearing failure. This is signaled by a metallic sound. An early replacement of a part can prevent the breakdown of more serious components.

Other reasons are described in the article: the washing machine is buzzing and making a loud noise during wringing, washing and a set of water.

Tripping of an RCD, difavtomat. In this case, do not restart the appliance. Shorting may be due to oxidation of the contacts, violation of the insulation of the internal wiring. To fix the problem, an inspection by a qualified craftsman is required.

Door jamming may be due to:

1. malfunctioning door handle;
2. electronics breakdown;
3. failure of the lever blocking the hatch.

Disconnect the device for 15 minutes from the network. If the problem persists after restarting, you should contact a specialist for further advice, or read our article: What to do if the washing machine door does not open?

Water drain does not start. The most likely cause may be a blockage in the valve or a breakdown of the pump. Cleaning and replacing parts will completely eliminate this problem. If the Electrolux washing machine does not drain the water after cleaning the filter, it is necessary to repair this particular element.

Top-loading washing machine does not stop the cycle. The most likely cause may be a failure of the electric heating element. The thermostat provides data on insufficient water level. Also, improper connection can cause a permanent drain of water into the sewer, thereby causing a constant filling of the system with water. You can eliminate the cause by restarting the program. You should contact the specialists if this method does not work, and the tips from the article did not help: “Why the washing machine does not drain the water and buzzing: what to do and how to drain the water? "

Spin mode does not work. The causes of the problem may be:

1. failed RPM sensor;
2. breakdown of the drain pump;
3. violation of the electronic module;
4. failure of the pressure switch;
5. failure of the electric motor.

We will talk more about this topic in the article: Why the washing machine does not wring out the laundry.

Basic codes of the washing machine Electrolux

• E11 - a problem with the intake of water from the home pipeline. The most common cause is a clogged hose or too low fluid pressure in the system.
• E12 - malfunction with water supply in the dryer (for models with this function).
• E13 - the presence of fluid in the pan. There is a crack in the housing.
• E21 - the machine does not drain water. The reason is tube clogging, a pump breakdown, or the washing machine is too low in relation to the sewer (the height difference cannot ensure a normal outflow).
• E23..24 - failure in the operation of the pump triac.
• E22 - there is no drain on the dryer. In this case, clogging of the capacitor is possible.
• E31..32 - a problem with the water level sensor. There may be blockages in the system or a malfunction in the electronics.
• E33 - Tena error, power surges.
• E35 - system overflow with water. Occurs when the level switch is broken.
• E36 - error of the water level switch and the heating tool.
• E38 - error of the pressure switch. Possible clogging of the feed tube.
• E39 - overpressure failure of the overflow.
• E41..45 - problems with the door.
• E51..54 - error of the control controller, there is no communication between the control center and the electric motor, problems with the relay and the tachometer.
• E55 - a malfunction in the motor circuit. Possible engine failure.
• E56 - tachometer error.
• E57 - too high current in the circuit. There may be a malfunction of the motor, exposure of internal cables or a malfunction of the control chip.
• E58..59 - an error in the engine of the electric motor due to a breakdown of the electric motor or electronics.
• E5A..E - problems with the electronics.
• E61..62 - prolonged heating of water, overheating. The problem is due to a malfunction in the device thermostat, heating element or central controller.
• E66 - malfunction of PETN or the entire heating system. It is more common when the equipment is used for a long time, as well as when using the Electrolux washing machine without a fine mechanical filter.
• E71 - breakdown of the thermistor.
• E72..73 - drying thermistor malfunction, short circuit in the circuit.
• E74 - incorrect position of the temperature sensor.
• E82..84 - failure of the electronics unit.
• E85 - malfunction of the main pump, pump failure.
• E91 - an error in the display board, there is no communication with the controller, it occurs when the connections burn out, as well as during bumps (during transfers, etc.).
• E92..99 - errors of the electronics unit.
• EA1..6 - malfunction of the DSP. It is connected with the failure of the engine belt.
• EB1..3 - voltage problems. They are connected with wiring malfunctions (inside the equipment and supplying the electrical appliance).

• EF1 - long drainage of water (due to malfunction of the pump).
• EF2 - strong foaming (unsuitable detergents used for washing).
• EF3 - pump wiring error, leakage, emergency pump operation.
• EF4 - no data from the flow sensor (water supply valve is closed).
• EF5 - stop the spin mode. The drum has a larger amount of laundry laid out according to the instructions.
• EH1 - power outages. Perhaps the board is not working properly.
• EH.3 - Problems with voltage level due to a malfunction of electronic components.
• EHE - fault relay protection circuit.
• EHF - protection circuit identification error.

Repair of the washing machine Electrolux (video)

The video details the problem with the electric motor. The method of removing and repairing device parts at home.

Knowing the most common codes, you can easily solve all the arising malfunctions of the Electrolux washing machine. Maintaining household appliances in good condition, proper operation and timely preventive maintenance will help to increase the trouble-free period of use of the appliance.