How to wash the hood in the kitchen from fat: how to clean the body, lattice filters using different means.

Almost every kitchen offers convenient appliances, as the exhaust system, which tends to be contaminated and to accumulate fat droplets on the walls and the grid. It's annoying all the housewives, as such pollution - especially chronic, it appears very difficult.

What must be done before washing the hood

Wash technique efficiently, without certain knowledge and skills in the home - it is impossible. The maximum that you can come up with an inexperienced housewife - is to wipe the wall and grille cloth, but fat is not such a procedure will remove. First you need to understand how the structure disassembled, because the assembled clean it is not possible to qualitatively.
Pre-hook or drawing:

1. Be sure before you start disassembling the device should be disconnected from the power supply to avoid electric shock.
2. In most technique should be a sticker with detailed instruction, which has a circuit design for disassembly. Usually the sides are retainers, they should otschelknut and lift the top cover.
3. When cleaning equipment from fat should be aware that a hollow tube, which closes with the hood with ventilation also needs a wash, because fat plaque accumulates in large quantities and there. Some craftsmen somehow prilovchilis change corrugation once a month or two, thus freeing himself from the tedious time washing. But not every technique will take a trick, since it is necessary to be able to do it right, otherwise you can break some detail and add to his problems.
4. Must be removed after the air filter. It's easy, it is also necessary to wash.
5. extract the shell itself is not removed, it is enough to wipe with a sponge and go to wash the other parts.

IMPORTANT! Carefully read the instructions in your drawing, as some models are turboair parts, that is, they can not be washed, they should be replaced.

How to wash the hood body

In addition to cleaning the internal parts, it is necessary to wash the well the outer housing art. Especially in need of washing is not built construction, since the main part of this drawing is hiding in the kitchen, and is located directly above the gas stove and collects all the soot and grease on himself.
All of this sticky substance deposited on the walls of the body and wash her, though simple, but quite uncomfortable, as is necessary to wash, standing on a chair and reach the top. Detailed instructions for washing the body:

1. Wet the surface with warm water.
2. Apply tablespoon spoon gel dishwashing on rigid sponge and put on a structure body, ensure that no liquid is dripped on a plate and the floor.
3. Rub hard and thick lip or brush the surface and leave for 20-30 minutes.
4. If stubborn dirt will help the lemon juice, the tool with the abrasive particles, on the type of soda, or strongly foaming agent for cleaning kitchen utensils and appliances.
5. After cleaning, rinse thoroughly with the chemical composition of all the water and walk it dry cloth.
6. Soft and dry cloth to wipe the surface washed to remove all stains and give the drawing shine.

IMPORTANT! Strongly inveterate fat cover on the body can be removed with a plastic scraper, a metal can not be used - hurt and scarred protective coating exhaust duct.

How to wash the grille from the hood

Grille - one of the components of the structure, thanks to its network structure copes with clean indoor air of particles of fat protects internal components and mechanism assembly from the oil flight. Taking all the dirt on themselves, it becomes yellow, sticky and bloated in appearance - clean up this design element difficult. Applying some effort, it is possible to wash the filter means of chemical or mechanical cleaning. In addition to the expensive formulations can use soap, it is perfectly corrode fatty plaque if soak the grille in soapy water, and then scrub with a brush remnants of contamination.

IMPORTANT! should be selected 72% of soap for cleaning the filter using a soap solution - it is easily rubbed on a coarse grater. After an hour soaking in some water so all the dirt will depart without difficulty, and the filter will shine again.

Processing soda solution

Almost all firms - manufacturers of exhaust technology, it is advised to wash both the front panel and internal parts and filter only mild soapy water or diluted gel washing utensils. However, this method works in all cases, it can be improved by adding to the composition of baking soda.
Master Class:

1. Pour into a bucket of hot water may be from the kettle or type of crane.
2. Pour into a bucket of water, a quarter cup of baking soda and a spoonful of dish detergent.
3. Stir the mixture of available tools, but not the hand, until a rich foam.
4. Cleaning Filter put into a container and leave to soak for 15 minutes.
5. Rub the product rigid sponge or brush and rinse in the bathroom shower.
6. Wipe dry with a cloth and put it back in the hood.

The outer surface of the hood can also saturate such a composition and to leave a few minutes after the brush wipe and rinse with warm water.

IMPORTANT! This method helps clean exhaust parts are almost always, but in very advanced cases it is necessary to boil the filter in soap-soda mixture of about 7-10 minutes, then the effect will be much better.

The use of ammonia

If the method with soda did not help, and the contamination remained on the filter and other parts of the kitchen device, you can try to clean them with ammonia. For the composition should be mixed in 4 liters of hot water floor alcohol tablespoon. When working with a staff necessary to wear a mask on the face, as the smell will be sharp and pungent, the same can burn the mucous membrane itself, open the window or window. Soak grating have about 2 hours then rinsed clean sponge and shower. Leave to dry or wipe the moisture with a cloth, paper towel.

As wash extract from fat using a soap solution

For the manufacture of the solution is necessary in 3 liters of hot water to dissolve half piece 72% soap. Small Circuits extract should be boiled in soapy mixture as grating and soak process scraper mechanically. Soap solution is slowly cleaves fat and oil, and after soaking dirt residues can clean off the rigid plastic scraper or a brush.

Processing acetic or citric acid

For the treatment of parts of the unit must take 9% vinegar and rub them all the details. Lattice can be soaked in vinegar solution for 15 minutes.

IMPORTANT! Clean in this way it is necessary to wear gloves and if the window is open.

For the lemon treatment is necessary to rid the lemon peel and cut into two parts. Pulp wipe all the mechanisms of the hood and the outer box, give the juice to soak for 10-15 minutes. After a rinse with water and wipe with a cloth.

IMPORTANT! If the grille is very dirty sticky touch of, you have to soak it in a solution of citric acid at night.

How to clean the grate by means of drawing means for cleaning drainpipes

This method is used when you need to remove the very long-standing pollution, which were saved by years. The liquid solution can be soaked for 25 minutes grating and other small items under suction and rinsed with hot water. If it is a powder, it is necessary to dissolve it in water and then carry the gadget routine.

How to clean up the kitchen hood filter grease

To clean this part drawing can be used a variety of means. Effective formulations based on charcoal. They contain a lot of alkaline components that are quickly cope with the fat and oil. Method cleaning member depends entirely on the degree of contamination:

1. Easy level. These are small droplets of fat is quite light in color, they are not yet frozen and remove them easily. Lattice then soaked for 3-3 hours in a soap or soda solution. After clean the remnants of dirt with a brush. It is necessary to wash the filter under hot water with detergent, gradually reducing the temperature. The main thing that the filter did not have any detergent or chemical agents, or the mechanism may be damaged.
2. Heavy erase. A situation in which a dark brown and ginger oil is on the drawing details. The most effective way - is digestion. In a container of water are added all the details and add grated soap pieces and 3 tablespoons of baking soda and boil for 30 minutes.

Well cleaned hood will be pleasing to the eye the owners and more productive work. Capital usually instigate cleaning every six months.