A heating battery has leaked and a pipe is flowing: what to do, how to fix it - Setafi

If an emergency situation arose and the heating battery leaked, you need to understand what to do first. Determine the place of the leak, put a container under it or put a rag. First, the gaps, the junctions are sealed using available methods. But in any case, repairs will be required, which should be carried out by the management company. The most common types of accidents and how to eliminate them are described in this material.

The content of the article

  • What to do right away
  • Elimination of leaks in the area of ​​\u200b\u200bconnection of the pipe and riser
  • Crack at the junction of sections
  • Leak in the contact area of ​​the riser and battery

What to do right away

If a pipe has leaked, the causes are often related to wear and tear. For example, cast-iron heavy radiators act with their weight on the hinges for a long time, do not bend, the contact point becomes thinner, which is why a leak occurs.

If a heating pipe is leaking, you need to understand what to do first. To do this, determine the place of depressurization:

instagram viewer
  • connection of the riser with the pipe;
  • a certain part of the pipe;
  • connection between battery sections;
  • leakage within one section of the radiator.

It is clear what to do where the heating battery drips:

  1. If there is a tap, it is immediately closed (position perpendicular to the pipe).
  2. A rag is immediately placed in the flooding zone (if there is very little liquid) or a flat basin is placed, another container (if there is quite a lot).
  3. Also, the radiator must be covered with a dense cloth so that splashes do not go to the wall.
  4. Immediately after that, they contact the management company or the HOA, the dispatcher of which must receive calls around the clock.
Heating battery leaked

There are also emergency cases when it is not clear what to do if the heating battery is leaking. For example, a rather strong gust was detected during the heating season (the water is very hot, even a small trickle burns). In such cases, one person must take the first measures described above, and the other must simultaneously call the rescuers by calling 112 or 01.

Elimination of leaks in the area of ​​\u200b\u200bconnection of the pipe and riser

Such leaks are often associated with improper installation or selection of pipes of the wrong diameter. Or too heavy objects were placed on the radiators for a long time, because of which they were partially damaged. For fixation, you can temporarily use a thick towel, but then as soon as possible it should be replaced with another material:

  • rubber (from bicycle wheels);
  • clamps for automobiles;
  • strong wire.

For reliable fixation, several strips of 5 cm wide (31 cm long) are cut from rubber. After the garter, it is recommended to fasten it over the entire surface with clamps.

Elimination of leaks in the area of ​​​​pipe connection

If a small crack is found, it can be repaired with a cement-gypsum bandage:

  1. Prepare a cement mortar of medium density.
  2. Cut several strips of bandage (length up to 25 cm).
  3. Soak them in the solution and wind them around the damaged pipe.
  4. Lay out 3 more of the same layers.

Crack at the junction of sections

In this case, it is difficult to determine the damaged area, so you need to constantly wipe the radiator and immediately look for the source of the leak with your eyes. Immediately after detection, the tap is closed so that no more water flows.

Then you need to reduce the pressure using the Mayevsky crane. If the water has already stopped dripping, you can proceed with the repair. Cold welding is used, and if there is no apparatus, the damaged part can be covered with mastic based on epoxy resins.

Now it’s clear what to do if the heating pipe is leaking:

  1. First, the surface is thoroughly cleaned of old paint.
  2. Then they take the steel cable and remove the rust.
  3. After that, they begin to weld or close up with mastic.

Since the composition dries for at least 2 hours, the battery is kept closed. At the same time, it is not necessary to apply repeated layers - it is enough to process the composition so that a surface with a thickness of 5 mm is obtained. In extreme cases, you can also paint a hot radiator; for this, heat-resistant paint is selected.

Leak in the contact area of ​​the riser and battery

To fix the problem, you need to do this:

  1. Close the tap.
  2. Drain all water from the radiator.
  3. Unscrew the fixing nut and remove the flax.
  4. Carefully remove the radiator from the riser.
  5. Connect again by inserting a new linen.
  6. Tighten the nut until it stops.

To understand what to do if the heating battery is leaking, you need to accurately determine the cause and location of the damage. Moreover, at first they take emergency measures so that the flow does not increase and, moreover, there is no rush. If there are doubts about the reliability, you should contact not only the dispatcher, but also call the rescuers.

Heating battery leaking

Moreover, it is important to understand that radiators and pipes belong to the general heating system of the house. Therefore, repairs are made not at the expense of the owner, but at the expense of the HOA or the management company, which collects monthly fees for the maintenance of the house.

Therefore, you can figure out how to repair if a heating pipe has flowed, eliminate the leak, and entrust the repair itself to specialists. After carrying out the work, they must draw up an acceptance certificate and indicate the terms of the guarantee.

Do-it-yourself stand for shovels and rakes: interesting ideas

Do-it-yourself stand for shovels and rakes: interesting ideasHomeGardenGarden Tools

Competent organization storage garden tools - the primary task of a self-respecting gardener. After all, the devices must be kept clean and dry, and always be at hand within walking distance. We of...

Read More
Diamond blade for concrete: own rating of the best manufacturers - Setafi

Diamond blade for concrete: own rating of the best manufacturers - SetafiHomeUncategorized

Diamond blades are produced by different manufacturers - Russian, Belarusian, European. When choosing for professional purposes, pay attention to durability, number of teeth, price and other parame...

Read More
What is a pitchfork, what is the tool for

What is a pitchfork, what is the tool forHomeGardenGarden Tools

Any gardener or land owner has a set of tools that allows them to take good care of the territory. There is enough work - the site needs to be dug up, weeds, debris and so on must be removed. One t...

Read More