Your dishwasher did an excellent job, but suddenly showed the error code on the scoreboard? So, there was a problem that needs to be fixed. Having deciphered the errors of Samsung dishwashers, you can quickly find the problem.
Sometimes failures are insignificant, so the user can eliminate them. Consider the fault codes of the Samsung PMM.
How to decode the trouble codes Samsung
What kind of malfunctions can be found in Samsung dishwashers? In the table below we have resulted in the decoding of each code, and also suggested ways of troubleshooting.
| DTC | What does the error mean? | Causes of appearance | What do we have to do |
| E1 | Long set of water. | 1. Lack of water supply in the system. 2. The water tap is closed. 3. The water inlet hose is clogged or clogged. 4. The door is not closed properly. 5. The filter-mesh was hammered. |
1. Turn off the tap and check for water in the water supply. 2. Turn the shut-off valve, it may have been blocked. 3. Inspect the water intake hose. It should be flat. Maybe he was bent or pinched by some object. 4. Close the door more tightly. It is equipped with a locking lock. While the lock does not lock the door, washing does not begin. 5. Clean the filter mesh. It is located in the junction of the filler hose with the PMM body. Close the water, unscrew the hose and rinse the mesh. |
| E2 | What is the error code: the machine does not drain the water after washing dishes. | 1. Problems with the drain hose. 2. The filter was clogged. 3. The drainage system was clogged. 4. The drain pump clogged in the car. |
How to fix a crash: 1. Inspect the drain hose that connects the dishwasher to the sewer. If it is pinched or twisted, water will not merge. 2. Located at the bottom of the filter is clogged with food leftovers. For normal draining, clean the filter. But first press the "Drain" button. 3. To check the drain hose for a blockage, unplug its end from the sewer and lower it into a bowl. If the drain does not occur, then you need to remove the hose and clean it of food and dirt. 4. In case of blockage, the drain pump can be cleaned by hand if you are familiar with the design of the dishwasher. But it is better to call a master. |
| E3 | No water heating. | 1. Defective TEN machine. 2. The thermostat broke. 3. The control module has failed. |
Self-repair if an error is detected: 1. Check that the connections are correct. If the car is new, you could confuse the hoses. 2. Check the set mode. If there is a delicate washing, the heating temperature will not exceed 40 degrees. 3. Examine the Samsung dishwasher filter for blockage. With reduced circulation of water, the heater does not turn on. 4. Check the heater. If it is overgrown with scum, then the element needs cleaning. If the heater is burnt out - a complete replacement is required. 5. Install a new thermostat in case of malfunction. 6. The cause of the breakage of the module, and also the replacement of the module can only be determined by the master. |
| E4 | The meaning of the code on the Samsung dishwasher: there is too much water in the tank. | 1. The sensor that controls the water level in the tank is defective. 2. Problems with the water intake valve. |
How to help: 1. Check the level sensor, replace if faulty. 2. Inspect the fence valve. Replace if necessary. |
| E5 | Water pressure too weak. | 1. Problems with the level sensor. 2. The dishwasher filter is clogged. 3. Clog or kink of the filler hose. |
1. Inspect the level sensor. In the event of a breakdown, the sensor needs to be replaced. 2. Clean the filter of blockage. 3. Check the water inlet hose. Adjust its location. |
| E6-E7 | Problems with the temperature sensor. | The thermostat does not work, the water does not start heating. | It is required to install a new temperature sensor. |
| E8 | An alternative valve has failed. | If a fault is found after the check, the valve is replaced. | |
| E9 | The program launch button does not work. | 1. The buttons of the button got detergents and it was stuck. 2. During the operation, the button was sold. 3. There was a short in the contacts leading to the button. |
The panel with the button should be disassembled and cleaned. Check the button's contacts, if they burned out - you need a replacement. |
| UC | Incorrect voltage in the network. | If the mains voltage is too low or too high, the dishwasher will not work, highlighting the error. You can wait until the voltage resumes, or call an electrician. | |
| EA | The water level in the dishwasher is exceeded. | 1. Problems with the drain hose. 2. Incorrect level sensor data. |
1. Inspect the drain hose. If it is pinched or clogged, the water will go badly from the machine. It is necessary to clean the hose from blockage. 2. Check the condition of the water sensor. If necessary, replace. |
| 3E2 | There is no signal from the vehicle. | It is necessary to check wiring connections between the engine and the device. | |
| Die | The door is not closed tightly. | Stronger press the door of the machine, otherwise the washing will not begin. | |
| Le | There was a leakage of water. | It is necessary to inspect the body of the dishwasher, determine and eliminate the cause of the leak. |
Before you begin to search for breakdowns, disconnect the Samsung dishwasher from the mains, shut off the water supply.
If the error on the screen is displayed for the first time, it is important to know how to reset the PMM. Reboot is carried out by disconnecting the machine from the network for 15-20 minutes. If after turning on the error again appeared on the screen - you need to look for a problem.
If you are not familiar with the dishwasher installation, entrust repair to a specialist. It is not difficult to damage the details, and it takes a long time to restore them.
