Faults washing machines Vestel( Vestel)

Contentsbuilding, and the instructions to the washing machine Vestel completely lost, you can find the cause of the failure yourself. Most often failures provoke such factors:

• Violation of operating rules.
• Low quality parts.
• Factory marriage.
• Special operating conditions( water quality, power surges, etc.).

The situations listed are usually rare, and the masters believe that each brand of washing machines has its own set of typical breakdowns. By the Turkish typewriters Vestel this also applies.

The following failures are typical for them:

• The Vestel washing machine does not turn on, the washing mode does not start. As for the control panel, it works in such cases, it is possible to choose the washing mode, but the “START” button does not work.
• The machine freezes immediately after starting the wash. In this case, the user selects the washing mode, starts it, and the machine, after 5-10 minutes of work, stops the process, the buttons do not respond to pressing. Error code E07 often accompanies breakdown.
• Do not pick up detergent.

The above malfunctions are specific to Vestel's SM brand and do not depend on water quality and other external factors, but are related to the features of the assembly technique.

The above list of breakdowns far from exhausts all possible malfunctions - there are a number of other failures, but we decided to pay attention only to the most frequent breakdowns in order to examine in detail their causes and remedies.

We will look into repair issues more deeply, and you can fix the machine with your own hands.

Important! If you are interested in replacing the bearing in the Vestel washing machine, then know that this process is time consuming, requires experience and effort, and the breakdown is rare and not typical for Vesteloc washers. If you manage to find in the stores an original bearing for the Vestel washing machine, then its replacement is the same as for other brands.

More information about replacing the bearing - in the video:

Helpers - fault codes of washing machines Vestel

In models equipped with an electronic display, you can figure out the reasons for this or that failure by decoding the alphanumeric codes. These codes appear on the board after each self-test machine.

Most often, Vestel machines issue the following error codes: E07, E01, E02.

The washing does not start in the Vestel

machine. At the indicated failure in 4 out of 10 cases, the UBL sensor( hatch locking device) breaks. Because of this, the controller believes that the hatch is open, and does not allow the wash to start.

There may be no breakage codes on the board.

What is the result? The door of the machine is locked, you click on the "START", but the process does not even think to start. How to start a search for the causes of breakdowns and how to repair a Vestel washing machine with your own hands, consider below:

• Disconnect the machine for 10-15 seconds.
• Turn on.
• If the problem is still with you, again turn off and turn on the AGR.
• Nothing has changed? Then act differently.

What to do next:

1. Disconnect the machine from the power supply.
2. Open the hatch cover.
3. Arm yourself with a Phillips screwdriver, loosen the 2 bolts holding the UBL.
4. Carefully reach UBL.

Caution! Sensor wiring is connected to the locking mechanism - do not tear off the wires.

1. Take a normal tester and measure the resistance at the contacts of the sensor UBL.
2. If the thermistor is in good condition, then the indicator will be at around 900 ohms.
3. In the event of a breakdown on the tester's display, you will see 0-1.

So you found the reason that the wash does not start. Your task is to replace the UBL, then all the processes in the AGR Vestel will be adjusted.

If you have determined that the locking mechanism of the hatch is not broken, then you need to look for the problem in the electrics - for this you need the electrical circuit of the Vestel washing machine. Each model has its own scheme - you need to look for it in the manual or on the manufacturer's website.

If there is no circuit, proceed according to elementary logic: disassemble the control panel and ring the chip.

Experienced specialists do not recommend doing such work on their own - they require certain knowledge.

The Vestel machine hangs when you start washing

Knowing how to disassemble the Vestel washing machine may be needed if the washer starts to hang by running the washing. As a rule, this happens either in the first minutes of washing, or at the very end.

In this case, it often happens that the machine is not quite “hanging” - the control panel can work, the indicators light or blink, and the display can show the washing mode code.

If the board shows the DTC E07, proceed as follows:

• Disconnect the washer from the mains: take the plug out of the socket for half a minute.
• Insert the plug into the network and start the wash. If the problem does not occur again, then the board rebooted and the error was fixed.
• If the problem persists, then turn off the machine and check whether it is installed correctly - for this, arm yourself with a building level. If the floor is crooked, and the legs are not adjusted, this can provoke a problem.
• The program may hang due to failure of UBL.Press the door tightly with your knee - if the action helped, this does not mean that you have to do it every time. This means that the problem is in the locking device and needs to be changed as described in the previous section.

Important! The problem of UBL can be recognized by the constant jamming of the hatch when opening after washing.

Much worse if the machine hangs and the E07 code is constantly on. If everything goes exactly in such a scenario, then the problem is in the electronic controller( module), and to solve problems with it, it is better to call the wizard.

Believe me, it is better not to try to make an independent repair of the control board - this is complex electronics, and for its reprogramming or repair you need skills, tools and knowledge. If something goes wrong, and you ruin the board, the repair will "fly into the penny."

Powder and rinse aid remain in the container of the Vestel

machine. The equally common problem of the Wasteral Vestel is washing laundry without powder. The bottom line: dirty laundry and wet unused powder in a cuvette. The receiver of the powder at "Vestel" ceases to give the powder due to the valve of filling the water in the tank.

For a strange and unexplained reason, the water inlet valves of the Turkish Vestel machines come into assembly with the marriage already from the factory. This marriage is so cunning that it often pops up after the warranty expires.

The essence of the breakdown is as follows: you start washing, the controller commands the valve to fill it. If everything is working properly, the valve opens and water flows into the tank, then the valve closes and the washing starts.

If the valve is defective or broken already during the operation of the machine, then it usually opens, but not at full strength. Watching the machine, you may notice that the water enters the tank more slowly and with weak pressure, almost without grabbing the container with detergent. As a result: the powder is in place, the quality of washing for C grade.

For your information! The machines of the brand Algy, Indesit or Samsung have a self-diagnostic system that recognizes the slow flow of water into the drum. When she notices this, immediately reports this code on the screen. But Vestel's cars often cannot do this - it is not known what the speed of water recruitment for Turkish manufacturers is slow.

There is no point in repairing a defective valve - it is better to replace it with a new one. How does this process happen:

1. Buy a new valve that fits your model CMA( Vestel Aura( Aura), Vestel Bora( Bora), etc.).
2. Disconnect the washer from all systems: electricity and water supply, sewage pipes. Take the car out of the niche if it is built.
3. Twist the bolts that secure the top cover of the CM and remove it.
   
4. A small filling valve( usually made of plastic) will wait for you under the lid, where the water intake hose is connected.
   
5. Remove the wires from the sensor.
6. Unscrew the fasteners that hold the valve, and remove it.
7. Take the new unit and install it on the same principle as it was removed: fasten the bolts, connect the wiring, close the lid and run the test wash at idle - no laundry.

We add that Turkish-made SMs cannot stand on a par with higher-quality models, but their plus is that many failures can be fixed without a master with their own hands. All you need is: comprehensive repair information, minimal tools and some free time.