How to iron a shirt in just 4 minutes

To quickly deal with the rumpled shirt, need iron and the correct sequence of actions.

Agree to go in a crumpled shirt worthless. For example, I learned how to skillfully get rid of the wrinkles in the clothes, and I want to share the experience with you. I'll tell you their secrets of how to iron a shirt quickly and efficiently!

Where to begin?

First we need to properly wash and dry clothes. If most of the clothes you can hang on the rope, the man's shirt should be well shaken and hang on a hanger.

Shirt is best to dry on a hanger, so there were fewer wrinkles and that is not stretched garment.

Now you need to figure out the tissue from which the sewn product. Usually this information is listed on a label on the reverse side of his shirt. It also gives recommendations to the temperature at which you can wash and iron this thing.

On the clothing label has useful information - at what temperature to wash and iron product.

At what temperature the iron you can remove creases thoroughly after washing a shirt? It depends on the type of fabric:

Picture	temperature settings
	Silk Weakest heating, not more than 110-120 ° C. Ideal - silk men's shirts do not iron at all. Enough of them to dry on a hanger, without spinning.
	Synthetics The recommended minimum temperature - 110-120 ° C.
	Cotton X / cotton fabric recommended iron at a temperature of 150-200 ° C. You can use a steamer.
	Wool Wool material will withstand heating medium - 150-170 ° C.
	Linen Flax shirt can be ironed at a very high temperature - 200-220 ° C.

Shirt ironed quickly and correctly

To pat his shirt, we need:

• Iron;
• Ironing board;
• Sprayed with water;

Instead, you can use the ironing board table covered with a towel.

All men's shirts before ironing needs a little moistened. For this process the fabric spray to "spray" mode, or take a not fully dried out after washing thing. The main thing is not to overdo it, we need a little damp, but not wet shirt.

Before ironing do not forget to treat the water, the collar, sleeves and cuffs of the product.

There are many ways how to iron a shirt. Some advise to start from the front side, the other - with the cuffs and collar. I suggest using the most effective method - move from simple to complex parts. Let's start:

Minute 1. Sleeves and cuffs

Once I began to stroke men's shirt from the back - it is the largest part of the product. Ironed this place, it seemed to me that most of the work is done. But I quickly realized, as it was not right. Let me explain why.

While you will be ironing the rest area, have repeatedly flip the shirt. Because of this, it will be back again crushed. It is a vicious circle. So I made sure to start treatment is necessary with sleeve men's shirt.

Instructions such:

1. Put the sleeve on the ironing board so that its lower part is laid as straight as possible;

You need to start ironing the shirt with the sleeves

1. Walk first iron the seam, Then the entire length;
2. Carefully otutyuzhte cuffs, Try to get the buttons and buttons;
3. Repeat steps a second sleeve.

Shirts with long sleeves is convenient to iron on a special stand, which modern ironing boards staffed.

The photo shows the direction in which the iron cuffs

Products with short sleeves should be ironed on the same principle. The procedure is simplified a bit - sleeve can be completely pull on the edge of the board and ironed immediately on both sides.

2 minute. The front and rear

With sleeves coped. Now we go to the site where the sewn buttons and collar area. Place the shirt on the ironing board, flatten it from the folds of his hands and carefully walk around iron.

In no case do not press the buttons on the iron. They can melt and ruin and a shirt and iron.

Narrowed side of the iron iron the material between the buttons.

Next, slowly dragging his shirt, go to the back. In the interim, do not forget to iron the seam side products, there can also be folds.

3 min. shoulders

To smooth rounded shoulders convenient to use part of the ironing board. Pull the shirt over it so as to completely see the desired zone. Walk iron nose to inaccessible places with increased pressure.

When you move from one shoulder to the other, proutyuzhte place by stitching the top and back of the product.

Shoulder seams and yoke require particularly careful handling. To avoid the formation of folds and deep wrinkles, again sprinkle them with water before ironing and carefully straighten hands.

4 minute. Collar

Properly ironed shirt for men in this zone will be easier if you can remove the seeds and by means of its collar. If they are non-removable, leave them in place.

Put the collar on the external side on the ironing board.

Collar need ironed, carefully pull the shirt.

To strengthen the effect with steam jacket. Fill with water, built into the iron liquid reservoir, and turn the special mode. All that's left to hang ironed shirt on a hanger and walk on it a jet of steam.

Steamer - perfect replacement iron, but often the price is high.

other methods

If the iron is not nearAnd shirt pat need to - there is a solution. Here are the three best ways to eliminate wrinkles:

1. Hot steam. Hang the shirt on a hanger in the bathroom and turn on the hot water. The steam will affect the wrinkled areas such as iron. It will only have to wait for the complete drying of shirts.
2. A special solution. Mix atomizer for laundry powder, hydrogen peroxide and pure water in the same proportion. Sprinkle this mixture shirt and hang cobwebs. After drying, all wrinkles smoothed;

Powder and peroxide is better not to use bright synthetic things as may remain ugly divorces.

1. Nemnuschayasya tissue. If the shirt is sewn from fabric that is not wrinkled, you're in luck. You can moisten it well and shake a couple of times dramatically.

results

I think you will be able to easily cope with any folds, because now you know how to iron a shirt. If you need a visual guide - watch the video in this article. If you have any questions, please comment.